Search found 156 matches

by secondtonone317
Fri Jul 08, 2011 12:35 pm
Forum: KA-T Picture Threads
Topic: S14 PICS only .... :-D must have pics in every post!!!
Replies: 519
Views: 183435

Image
by secondtonone317
Thu Jun 30, 2011 6:25 am
Forum: Drag Racing
Topic: Tuned it to 24psi, but **** runs...
Replies: 14
Views: 4796

Well it wasn't covered...thats why you got flamed for bringing up an old thread. Cory drives an S2000...not sure wtf happened to his KA-T. While I'm here I'[l give you a quick review of the Hallman PRO RX boost controller. It works well and I really glad I got the in-car boost control knob. I have ...
by secondtonone317
Thu Jun 23, 2011 5:14 am
Forum: Drag Racing
Topic: Tuned it to 24psi, but **** runs...
Replies: 14
Views: 4796

figured I would search and use an existing thread rather than getting blasted for making a new one with a topic that was covered already
by secondtonone317
Wed Jun 22, 2011 9:25 am
Forum: Drag Racing
Topic: Tuned it to 24psi, but **** runs...
Replies: 14
Views: 4796

any more feedback on the hallman?
Which model?
Does it hold boost then open at set PSI or does it let the gate open a little bit before desired psi.
by secondtonone317
Wed Jun 22, 2011 9:07 am
Forum: KA-T Tech. Basic
Topic: Manual Boost Controller or Electronic (Non ECU CONTROL)
Replies: 11
Views: 2438

My greddy profec B II is also being a pain in the ass. one night I hit it and noticed that I did not hear the gate dump so I let off, I thought the solenoid went bad, I swapped that and still same issue. When I turn the unit off the gate opens on spring psi, I will check the wiring to the solenoid a...
by secondtonone317
Tue May 17, 2011 7:17 pm
Forum: KA-T Chat
Topic: Meth injection
Replies: 64
Views: 7655

Will buy a kit tomorrow, looking at this one
opinions greatly appreciated, with summer heat coming meth will be good for heatsoak
http://www.coolingmist.com/detailmain.aspx?pid=STMClear
should I go 150 psi or 250? I was opting for 250 for better atomization and having it kick on at like 15psi
by secondtonone317
Thu May 12, 2011 5:21 am
Forum: Dyno Results
Topic: Pump Gas dyno #s
Replies: 20
Views: 5091

Yes, I asked the previous owner about the ignition, he said the car never broke up because of spark so he left it alone.
by secondtonone317
Wed May 11, 2011 7:45 am
Forum: Dyno Results
Topic: Pump Gas dyno #s
Replies: 20
Views: 5091

this car motivates me. me too must get another s14 asap! car is a beast, got a little taste of boost again in the passenger seat, aww how i miss it soo.. q45 gears makes this car so much fun, so bish.. swap out the gt30 for a 6262 :twisted: :twisted: LOL, IDK man. Its so good right now I don't want...
by secondtonone317
Wed May 11, 2011 5:37 am
Forum: Dyno Results
Topic: Pump Gas dyno #s
Replies: 20
Views: 5091

Yes this is on stock ignition. Since I got the car all I really did was the Q45 rear end swap with 3.54 gears. The car was spinning on the dyno, the first 3 pulls we did in 3rd then the last one we decided to try 4th. It still spun a little but not as bad. In the original vids you can see the tires ...
by secondtonone317
Thu May 05, 2011 12:49 pm
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

after you sir, lol
by secondtonone317
Thu May 05, 2011 12:22 pm
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

I really think a GPS speedometer is the best solution but those things are expensive, probably more expensive than what this swap cost me.
by secondtonone317
Thu May 05, 2011 5:55 am
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

thanks guys, I will give this a shot.

http://forums.nicoclub.com/how-to-speed ... 92355.html
by secondtonone317
Wed May 04, 2011 5:57 pm
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

I think you mean if speedo says 70 im doing 77? Since it would normally take 4.09 turns of the driveshaft to make one wheel rotation, it now takes 3.54 turns to do the same, so less turns more speed? Plus my wheel size is larger but not trying to factor that in right now. Yeah, you're right. I'm ru...
by secondtonone317
Wed May 04, 2011 11:03 am
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

this calculator looks like it might help but its not working

http://www.csgnetwork.com/rgpspeedcalc.html
by secondtonone317
Wed May 04, 2011 10:55 am
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

S13: http://forums.freshalloy.com/showthread.php?t=111713 S14: http://forums.freshalloy.com/showthread.php?t=124389 According to my quick calculations, your gearing makes your speedo about 9% off, assuming your tires have the same rolling diameter is stock. So, if you're speedo says 70mph, you're a...
by secondtonone317
Wed May 04, 2011 9:03 am
Forum: Car Chat
Topic: JDM tyte 3rd brake light - I want (notice the WANT not NEED)
Replies: 11
Views: 2357

if anyone is willing to buy this they deserve props
by secondtonone317
Wed May 04, 2011 6:16 am
Forum: KA-T Tech. Basic
Topic: 3.54 rear gears swapped in, how can I get speedo calibrated?
Replies: 20
Views: 2702

3.54 rear gears swapped in, how can I get speedo calibrated?

I swapped in 3.54 gears into my car last night using a 1994 Q45 rear end, hubs, drivers side axle, z32TT drivers side axle. I'm sure you are all familiar with this swap. I did some searching on here, google, and other 240sx forums and didn't find much. How can I get the speedometer to read correctly...
by secondtonone317
Mon May 02, 2011 1:15 pm
Forum: KA-T Tech. Basic
Topic: Help! WTB a good Clutch kit for 400hp++
Replies: 18
Views: 2388

I have an excedy twin disc and it works well
by secondtonone317
Thu Apr 28, 2011 12:22 pm
Forum: Motorsports and Meets
Topic: Car meet 5/1/11 12pm 'hood Garage
Replies: 1
Views: 1306

so close but this is the first I am hearing of it
by secondtonone317
Thu Apr 28, 2011 12:21 pm
Forum: KA-T Tech. Basic
Topic: how needed is an oil cooler?
Replies: 15
Views: 2017

anyone tried this ISIS kit? I might take a swing at it in the future.

http://aceupmotorsports.com/products/IS ... A24DE.html
by secondtonone317
Wed Apr 13, 2011 10:07 am
Forum: Car Chat
Topic: 454 big block?
Replies: 12
Views: 2093

Do it, the 454 has so much potential. To give you a hint my boys car runs 8's all day with a 302 in his car. ya, dont mind the other 30k that it takes to make a descent 8 second ride :roll: All it had was a cam, headers, intake, and holley carb. Stock heads, no nitrous. Trapping 199mph Wow, you sur...
by secondtonone317
Wed Apr 06, 2011 9:15 am
Forum: Welding/Fabrication
Topic: D.I.Y Motor Mounts
Replies: 33
Views: 13744

Nice idea, lots of better options out there but whatever floats your boat.
by secondtonone317
Wed Apr 06, 2011 6:46 am
Forum: Introductions
Topic: New from Guatemala, Central America
Replies: 2
Views: 811

welcome, cant wait for more pics
by secondtonone317
Wed Apr 06, 2011 6:33 am
Forum: FWD KA-T
Topic: Another boost altima
Replies: 3
Views: 1758

Welcome, do you ever go out to the headlighttheory meets?
by secondtonone317
Tue Apr 05, 2011 11:35 am
Forum: Supercharged KA's
Topic: supercharged hardbody lives!
Replies: 15
Views: 6684

nice build man, love the looks of the truck, must be fun, very tail happy?
by secondtonone317
Tue Apr 05, 2011 5:22 am
Forum: Introductions
Topic: Back at KA-t.org with my 2nd 98 240sx
Replies: 6
Views: 1311

are u fawkin serious he sold it? damn, we kept meaning to meet up some time. so does it still have that mean 3076 setup? ish is like 440/460 on pump gas, sounds crazy. Yes it still has the same setup with the full race twin scroll manifold......car is beasty, I have been taking it easy as to not ge...
by secondtonone317
Tue Apr 05, 2011 5:20 am
Forum: Introductions
Topic: Back at KA-t.org with my 2nd 98 240sx
Replies: 6
Views: 1311

koukidriver wrote:Glad your back with us,lol.
Glad to be back bro
by secondtonone317
Mon Apr 04, 2011 10:14 am
Forum: Introductions
Topic: Back at KA-t.org with my 2nd 98 240sx
Replies: 6
Views: 1311

lol, that mustang is like 600whp....I still have to get used to this car, the rear tends to get loose easily
by secondtonone317
Mon Apr 04, 2011 8:47 am
Forum: Introductions
Topic: Back at KA-t.org with my 2nd 98 240sx
Replies: 6
Views: 1311

Back at KA-t.org with my 2nd 98 240sx

I had a black 1998 240sx before, was going to go KA-t with it, ended up selling it, then about a year after(currently) I purchased a car that is probably well known to some of the members on here. I got it from a nice guy by the name of Ben, user name Pearl240sx. It's another 1998 240sx, pearl white...