www.ka-t.org

subject has been covered a million times before. search. search. and search again,,,,,, then if you dont find an answer read some builds......

My build is very close to yours except its a DE. Im going to get the machine work done in san diego within the next month or two... have you picked out a machine shop? Where are you in cali? You should look into megasquirt incase you havent its a lot cheaper and has a lot of future expandability, i...

whats going on guys im building a SOHC boosted, its my daily so im building a seperate motor. parts list cp low comp. pistons eagle rods o&j valves o&j springs o&j stage 2 hydro. cam cx top mount t3 mani turbonetics t3/t4 turbo now my question is since its my daily can i have the motor b...

i seriously just read 19 pages of this thread and its not done? holly s**t...... none the less the car looks really good, its almost identicle to the set up i wanted,,,, why are you switching from haltech to AEM???

I still think you should consider investing in a new BOV (hint..hint.. Tial, etc.) just to be on the safe side even though you haven't experienced any problems/leaks yet. * if his BOV went bad wouldnt he just have turbo flutter? clean looking motor. im building a same set up with the cx mani but il...

dont like very many 2 tones but yours is very clean, good job

test the coil, the spark could have been to weak to get it started

sweet deal take it that the oil pump was the issue?

what ever happened with the car? did you turbo it again?

Id go with the higher cr pistons since you are going to lose about a point by putting them in an E motor so the 10.5s should put you at around 9.0 to 9.5 give or take . If you go with the 9.0s for a de motor you might end up with lower compression than you want . It totally depends on the boost lev...

Doing it right is to order oversized pistons and get the block machined out to match them. But if you scored some free parts, by all means try just throwing them in there. Yeah I know that's what I am doing I'm buying 1mm over wiseco pistons, that's the point of this thread the pistons come in 2 co...

I read that thread and it didn't help to much other than he has de pistons on his SOHC with a cr of 9.1:1, and if the satement is true switching to 10.5:1 in a SOHC it would go to 9.5:1, so I should do the 9.1:1 cr DOHC pistons cuz boosting on lower compression is better correct? I'm buying new pist...

i know this has been covered 1000000 times but to me this is a lil more complex, I've searched and only got stuff about SOHC pistons in a DOHC to raise compression. my plans are to go KA24E-T keep in mind i might need to bore my block to +1.0mm the only company found that sells pistons that size are...

has a car meet in 2 weeks, any locals going?

been a few months, update on this?

what tomei oil pump is that? l6/ l4?

i didnt expect the pin outs to be the same, i just want to have total control over my motor with out any lag and have the coils, the reason i dont want to go to a shop to have them do it is how am i gonna learn this stuff if i dont teach myself and ask questions? if that was the case i wouldnt be as...

thats the think aem doesnt have a connector for the SOHC just the DOHC. how many more sensors are on the DOHC that the SOHC doesnt? all this electrical stuff is equvalent to a 3rd grader doing trig to me, i dont get almost all of it. i have a basic idea and i remember reading about the distrib delet...

ive called a few shops and thier techs are busy, does anyone know if i can use the DOHC harness on the SOHC and just match wires? the reason i want the series 2 is cuz it has the coil outputs and i want to do the LS coils and elininate the distrib. or if someone has a better ems pointers would be he...

this things bad, did you run the chevy coils or what did you do with that?

I personally like my food a lil hot so I put a little bit of red peppers in mine.

That's close. Do a 50/50 mix of Italian and warstershire (idk how to spell it) let the breast soak for an hour or so wrap in Bacon throw on the bbq till the Bacon is done. So good

I got a good recipe pm me trust its one you'll try every time

Mine was when I was 11 restoring my g-pa el camino with my pops. (Needless to say neither one of us recived it) then doing Jr drags at 13 hitting the 1/8 mile and building our engines for the next weeks race was no other, moving between my 2 gmc sierras Camero and g35 I've done work on them all. the...

trying to get the IE put together for the 3rd annual s chassis meet meet up point will be at the corona plaza shopping center in front of the Sears outlet center. 492 N Main St, Corona, CA 92880. meet up time will be at 11:00. we will roll out at 11:30. lets try to get as many cars as we can from mo...

I'm just starting the turbo world so no I'm not gonna go post on threads to help out and try to act like I know what I'm talking about. And if you want to assume that I'm here to get a question answered then cool that's what you think your entitled to your opinion I know why I'm here and that's all ...

The thing is a moderator didn't become one by automatically knowing every thing. They asked questions did research and **** like that so it pisses me of when they don't give the time to shed some light like they were given who knows how long ago.

These things are a lot funner to build without spending mega cash. Do you really have 9k to spend on the car? You sound exactly like me when I first I first started asking questions. Stay around and read a bit, lots of info that will save you time and headack. I do have the cash for it and my car l...

if you don't like this forum you can leave. honestly this is the most helpful forum ive been to. i can tell you every miata forum ive been to has to be the worst help ive ever gotten. i post a question and its like a million tiny's, that have no clue what they are doing, swarm the thread. I never s...

Granted setups are different but they all require same items i.e fuel, pistons, rods, etc. If you cannot figure it out for yourself, then you should not be in this game. If you spend 9K on an engine, you better fly to the moon. Most people only put about $1200 in a short block which can handle 500w...