Search found 259 matches

by Gotenks64
Mon May 21, 2018 6:03 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

supersayianjim wrote:bump, what became of this car???
I still have it! It runs - I am in the process of fixing the trans potentially sell it.
by Gotenks64
Wed Jun 22, 2016 4:27 am
Forum: KA-T Tech. Basic
Topic: New Driveshaft
Replies: 0
Views: 950

New Driveshaft

I tore the stock rubber coupler on my stock driveshaft (picture is in my build thread). My question is since I have a N/A 300zx differential do I need the driveshaft-shop DRIVESHAFT with or without ABS? My car did not come with factory ABS, nor does it have ABS. Thanks! http://www.enjukuracing.com/p...
by Gotenks64
Sun Jun 19, 2016 7:12 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Q45 Caliper with Sentra Rotors.

Image
by Gotenks64
Sun Jun 19, 2016 7:10 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

So a few things have happened. I went a SPEC stage 3 clutch. I had a stage 3+ before, but I am not pushing anything near 380wtq. Second to that, when I installed the motor the second time I reused the stage 3+ a few years ago. I think I should have broken it[Stage 3+] in again because at that time I...
by Gotenks64
Fri May 27, 2016 7:07 am
Forum: KA-T Chat
Topic: ka24det wont start
Replies: 16
Views: 3653

Re: ka24det wont start

Make sure you are keeping an eye on that oil.... if you are flooding it you'll wash the cylinder walls. I would change it!!
by Gotenks64
Sat May 21, 2016 11:38 am
Forum: KA-T Picture Threads
Topic: Adam's formerly supercharged... now soon-to-be-turbo'd, S14
Replies: 777
Views: 211883

Re: Adam's formerly supercharged... now soon-to-be-turbo'd,

Damn bro sorry to hear that. Who put the bottom end together? What oil where you running?
by Gotenks64
Wed May 18, 2016 6:04 am
Forum: KA-T Chat
Topic: Gasket Removal
Replies: 3
Views: 1219

Re: Gasket Removal

The rear seal on the tranny yeah. I'll have to get a few cans of brake cleaner. The S**T is really on there.
by Gotenks64
Tue May 17, 2016 1:57 am
Forum: KA-T Chat
Topic: Gasket Removal
Replies: 3
Views: 1219

Gasket Removal

I am trying to get all of the gasket of out the lip. What do you guys usually do and use? This is the back of the transmission.

Image
by Gotenks64
Mon Apr 04, 2016 6:02 pm
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Ok! So is running strong, BUT my clutch started slipping.... I have a SPEC Stage 3+. It only slipped on setting B with is about 16psi. I dropped the transmission and took the flywheel to the machine shop. They said I have obvious hot spots. I will show you guys the clutch as the flywheel is at the m...
by Gotenks64
Mon Sep 14, 2015 5:24 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Quick video on my way to drill!

https://youtu.be/9XoTJ9gwsRs?t=1s
by Gotenks64
Sat Aug 29, 2015 6:57 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

What was your 60ft on that run? The best I can get is 2.1 with street tires. I want slicks cuz if I cut a 1.8, that is an 11 second run. 2.317 with my crappy AutoGrip tires LOL All I want is a 12 second run and I'll he happy 60ft is so hard with these cars... Best I ever had was a 1.9 for a high 12...
by Gotenks64
Tue Aug 25, 2015 4:36 am
Forum: KA-T Tech. Basic
Topic: For those of you with Holsets..
Replies: 1
Views: 731

For those of you with Holsets..

I have a Hy35, I am not running an oil restrictor but I am starting to think that I need one. I have a 12m x 1.5mm banjo fitting on it as of now. For those of you running one, where did you get your restrictor? I cant find any .063 or larger ones.
by Gotenks64
Mon Aug 24, 2015 3:44 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Since I have had the car the Water Temps of the motor have been at about 200* This is in 100 degree weather or 60-70 degree weather. I thought that adding the oil cooler may change it abit but it didnt. Over the weekend I put in a ISIS colder Thermostat and this has seemed to alleviate my issues. Sh...
by Gotenks64
Wed Jul 15, 2015 4:00 am
Forum: KA-T Picture Threads
Topic: seth's zenki build
Replies: 54
Views: 13674

Re: seth's zenki build

Glad you decided to keep her!
by Gotenks64
Sun Jul 12, 2015 8:42 am
Forum: KA-T Picture Threads
Topic: Single Slammer Build
Replies: 26
Views: 5460

Re: Single Slammer Build

Who makes the 880cc injectors that you are using?
by Gotenks64
Wed Jul 08, 2015 7:12 am
Forum: KA-T Chat
Topic: Oversize valves
Replies: 5
Views: 1837

Re: Oversize valves

I am no expert, but it depends on your hp goals. if you aren't going for max hp the larger valves will slow the velocity of the incoming air. this will hurt you in the low and mid-ranges of your power band.
by Gotenks64
Tue Jul 07, 2015 5:59 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

I have a few little things I am doing, but the car has been running well. I have a few small problems that I need to fix namely Valve cover leaks from the clear coat I think the machine shop put on the head. Transmission rear seal(under my car is pretty caked with gear oil) Steering is sloppy( Rack ...
by Gotenks64
Tue Jun 09, 2015 12:57 am
Forum: KA-T Chat
Topic: Best oil for ka-t
Replies: 14
Views: 3134

Re: Best oil for ka-t

I run rotella synthetic 5w-40 myself, and it works great!
by Gotenks64
Mon Jun 08, 2015 11:07 pm
Forum: KA-T Picture Threads
Topic: S14 2.44L KA-T Build
Replies: 40
Views: 10870

Re: S14 2.44L KA-T Build

Looking good so any details on what components you'll be using?
by Gotenks64
Mon Apr 27, 2015 5:34 am
Forum: KA-T Tech. Basic
Topic: Crank Pulley bolts shearing!!
Replies: 2
Views: 919

Crank Pulley bolts shearing!!

I have been driving my car pretty spirited since the tune. There are 6 bolts that hold the section of the crank pulley responsible for the water pump/ PS pulley, I only have ONE of this bolts in. They have all sheared off, I am thinking about buying a new crank pulley. Has anyone ever had this issue...
by Gotenks64
Thu Mar 19, 2015 9:28 am
Forum: KA-T Tech. Advanced
Topic: ka24de iacv aac delete questions
Replies: 1
Views: 1633

Re: ka24de iacv aac delete questions

You need to adjust the TPS sensor, so it shows idle for the amount you crack it open. I think idle voltage from the TPS is .45v to .55.
by Gotenks64
Thu Mar 19, 2015 9:05 am
Forum: KA-T Picture Threads
Topic: S14 KA-T Build - Kgriffin
Replies: 36
Views: 6582

Re: S14 KA-T Build - Kgriffin

How does your timing look at idle in NIStune and Base timing? Also is it running too lean? Whats the injectors you are using?And the latency you have them at?
by Gotenks64
Thu Mar 19, 2015 9:05 am
Forum: KA-T Picture Threads
Topic: S14 KA-T Build - Kgriffin
Replies: 36
Views: 6582

Re: S14 KA-T Build - Kgriffin

How does your timing look at idle in NIStune and Base timing? Also is it running too lean? Whats the injectors you are using?And the latency you have them at?
by Gotenks64
Sat Mar 14, 2015 8:52 am
Forum: KA-T Picture Threads
Topic: Jimmy's - '91 Nissan 240sx/Silvia ★ SuperOK! ★
Replies: 46
Views: 11384

Re: Jimmy's - '91 Nissan 240sx/Silvia ★ SuperOK! ★

This is a super clean build I love it!
by Gotenks64
Sat Mar 14, 2015 8:52 am
Forum: KA-T Picture Threads
Topic: Jimmy's - '91 Nissan 240sx/Silvia ★ SuperOK! ★
Replies: 46
Views: 11384

Re: Jimmy's - '91 Nissan 240sx/Silvia ★ SuperOK! ★

This is a super clean build I love it!
by Gotenks64
Thu Mar 12, 2015 4:53 pm
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

supakat wrote:Nice pick up. You can replace it but just bend it back for free. It only serves to change gears. Put it in each gear and turn the input shaft while looking at the output shaft to make sure it spins.
Thanks Supa, Ok i'll do that. Which kit do you have again? I need to start saving lol
by Gotenks64
Thu Mar 12, 2015 3:56 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Picked this 300z transmission up for 100 http://i1205.photobucket.com/albums/bb422/Gotenks64/Mobile%20Uploads/20150311_050102.jpg this worries me though... I didn't see it till I got home, is this replacable? http://i1205.photobucket.com/albums/bb422/Gotenks64/Mobile%20Uploads/20150311_050119.jpg
by Gotenks64
Fri Mar 06, 2015 7:13 am
Forum: KA-T Picture Threads
Topic: Gotenks64's ongoing build
Replies: 104
Views: 33894

Re: Gotenks64's ongoing build

Fuel pressure is about 43psi which is around stock. I took it out on 10 psi and then on 15......WOW this thing feels like a train and just keep pulling through the whole RPM range. I think I am going going to leave setting A at 10psi and setting B at 15. I need to get a GoPro so I can do an in cabin...
by Gotenks64
Fri Mar 06, 2015 7:06 am
Forum: KA-T Picture Threads
Topic: Kill3rwill's thread
Replies: 22
Views: 3514

Re: Kill3rwill's thread

supakat wrote:A better option of than the HX40 is an HE351. This is the turbo I am running now which is basically a HX35/40 Hybrid. 60mm comp 60mm turbine with a 9cm^2 T3 housing. Good thing about Holset, is you can sell them pretty easily if you want to get another turbo.

I agree! I am loving my Holset
by Gotenks64
Fri Mar 06, 2015 4:46 am
Forum: Dyno Results
Topic: Hy35 15psi
Replies: 6
Views: 4855

Re: Hy35 15psi

Yea man, I actually ordered mine off their eBay Store a little cheaper than what their site shows. The messages me letting me know that they were hand welding the end tanks to the core then shipping it to me. Atleast it's assembled in America! Haha nice! I am going to check out eBay. It snowed like...