Search found 152 matches

by Drift99
Sat Apr 13, 2013 10:49 am
Forum: KA-T Tech. Advanced
Topic: Running like crap 3 days before drift event
Replies: 5
Views: 2088

problem fixed! it turns out the MAF plug was shot. I soldered a new one on and all is good!

I appreciate the help guys!
by Drift99
Fri Apr 12, 2013 5:34 pm
Forum: KA-T Tech. Advanced
Topic: Running like crap 3 days before drift event
Replies: 5
Views: 2088

if both mafs aren't working double check wiring Whats a good way to check the wiring? Just check for continuity? I recorded a vid today of a cold start. The idle was perfect for the first few seconds and then the ATF went lean in a instant and it died. This is what happens only on cold starts. On w...
by Drift99
Fri Apr 12, 2013 5:29 pm
Forum: KA-T Tech. Advanced
Topic: Running like crap 3 days before drift event
Replies: 5
Views: 2088

Since you let it sit for so long did the batt need recharged(Erasing where you had your fmu set)? Could also be the engine temp sensor(A bad one will make it run/idle bad/rich) . It doesn't seem to be a vacuum/fpr/injector problem b/c the engine makes fine afr's until it starts to act up. Have you ...
by Drift99
Thu Apr 11, 2013 6:40 pm
Forum: KA-T Tech. Advanced
Topic: Running like crap 3 days before drift event
Replies: 5
Views: 2088

Running like crap 3 days before drift event

Alright I need some help My KAT is running like crap and I have a drift even on sunday that I have been waiting for for over 6 months. Here is the story; I was daily driving the car without problems. I park it for about 1 month. Yesterday I fired her right up for the first like since I parked it. It...
by Drift99
Tue Feb 12, 2013 5:40 pm
Forum: KA-T Tech. Basic
Topic: Cooling system filling up with air
Replies: 9
Views: 1805

Thanks guys. I thinnk your right kruked. It must be overheating. Since the temp sensor is reading air temp in the upper hose, I am not aware of the overheating. I will look around once again for leaks. I will change the liquid gasket for the pump and thermostat. I believe I might have a small HG lea...
by Drift99
Sun Feb 10, 2013 7:27 am
Forum: KA-T Tech. Basic
Topic: Cooling system filling up with air
Replies: 9
Views: 1805

Cooling system filling up with air

Hey guys I have recently swaped my blown KADE for another stock KADE. This one seems to be in much better shape then the old one and has 180psi across all four. I have properly bleed the cooling system twice now and each time my car started overheating (not too badly) after a week of DD. I spent a g...
by Drift99
Thu Jan 17, 2013 4:54 pm
Forum: KA-T Tech. Basic
Topic: Fuel filter question
Replies: 8
Views: 1760

get the oem 300xz filter. its bigger and flows better
by Drift99
Tue Jan 15, 2013 10:21 am
Forum: KA-T Tech. Basic
Topic: Bee-R Rev limiter wont go above 5000rpm
Replies: 1
Views: 769

Bee-R Rev limiter wont go above 5000rpm

Hey I purchased a Bee-R Rev limiter for my my 93 s13. I followed these instructions and am 100% sure I got the wireing done right. http://forums.nicoclub.com/bee-r-rev-limiter-on-ka24de-92-240sx-t380227.html The problem im having is that the limiter wont go above 5000rpm. Rev1 (with ebrake down) goe...
by Drift99
Fri Dec 28, 2012 8:46 am
Forum: KA-T Chat
Topic: Aftermarket radiator question....
Replies: 12
Views: 3130

I run an OEM R32 GTR rad. It bolted right into my hatchback. Its much thicker then my stock rad
by Drift99
Tue Dec 25, 2012 1:43 pm
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Cc wb 6 puck is rated for 500 but some say it wilp hold 600 Nice. I got this clutch in trade and was told it would hold 500, but I will be pushing for more than 500 eventually (hopefully closer to 600). This gives me hope that it may hold up ok. Alright thanks. So its somewhere between stage 4-5 i ...
by Drift99
Tue Dec 25, 2012 7:27 am
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Hey guys I have one more question.. What stage would you guys say the "Competition Clutch - Nissan 240SX "WHITE BUNNY" Upgrade" is? Stage 2 or 3?

Thnx
Jake
by Drift99
Mon Dec 24, 2012 1:31 pm
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Good to hear.
Thanks guys, ill let you all know how I like it in a few days :D
by Drift99
Mon Dec 24, 2012 10:59 am
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Alright the clutch just came in. I noticed that the clutch face is like the OEM pattern. On the Enjuku site the face had a bit different pattern (less cuts, more surface area). Did I get the right clutch? I ordered the Competition Clutch - Nissan 240SX "WHITE BUNNY" Upgrade http://www.enju...
by Drift99
Sun Dec 23, 2012 8:32 am
Forum: Car Chat
Topic: Hydro E-Brake with stock calipers
Replies: 4
Views: 2073

oh alright. I might grab a Ksport in the near future. thanks for the help
by Drift99
Sat Dec 22, 2012 3:16 pm
Forum: Car Chat
Topic: Hydro E-Brake with stock calipers
Replies: 4
Views: 2073

Oh alright. Wouldnt I need something like a one way valve though so I wouldnt be locking up all four wheels?
by Drift99
Sat Dec 22, 2012 10:12 am
Forum: Car Chat
Topic: Hydro E-Brake with stock calipers
Replies: 4
Views: 2073

Hydro E-Brake with stock calipers

Hey Im trying to get my hatch ready for the drift season and would like to find out if its possible to use a hydro ebrake with stock rear calipers? I was thinking of hooking up a clutch slave cylinder to the cable..? Is it doable? Has anyone tried this before? All my money is going to into an RB25 s...
by Drift99
Tue Dec 18, 2012 5:18 pm
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

thanks guys for narrowing it down. I just made my order for the White bunny full faced clutch. I spend 30 minutes in gridlock every weekday so im sure I will be thankfull for not getting the 6 puck. Going with this setup also saves me time and money for resurfacing my flywheel since it comes with an...
by Drift99
Mon Dec 17, 2012 7:39 pm
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Thanks guys

The exedy stage 3 and white bunny are both out of mu price range. I'd like to stay under $400 at my door.

I found a SPEC Stage 3 Clutch for $300 on Enjuku which is said holds upto 380 ft/lbs. Would you guys say it would hold up to the abuse? Any other recommendations would be great too.
by Drift99
Sun Dec 16, 2012 7:38 pm
Forum: KA-T Tech. Basic
Topic: Clutch Questions/Recommendations
Replies: 25
Views: 3127

Clutch Questions/Recommendations

Hey So today I finished installing a KADE in my s13. I took her for a drive and the clutch was slipping badly. I dropped the trany to find out it had an exedy stage 1 in it. The clutch wasnt completely worn smooth but a few groves on the "non flywheel" side were full of pad dust. The flywh...
by Drift99
Sun Dec 09, 2012 11:16 am
Forum: KA-T Tech. Basic
Topic: Quick Q about belt/pulley
Replies: 2
Views: 742

problem fixed. i figured out that the crank pulley can be taken apart and swapped without even removing it off the crank
by Drift99
Sun Dec 09, 2012 8:58 am
Forum: KA-T Tech. Basic
Topic: Quick Q about belt/pulley
Replies: 2
Views: 742

Quick Q about belt/pulley

Hey Im in the middle of swapping out a hicas steering pump on my new kade to a regural pump. I noticed that the hicas pumps are run by a wider belt (4 notch) then compared to the regular pumps (3 notch). I changed the water pump pulley to the 3 notch pulley already. I would like to find out if I nee...
by Drift99
Tue Nov 27, 2012 3:17 am
Forum: KA-T Tech. Basic
Topic: 12 point bolt in block. What size is it?
Replies: 7
Views: 1263

thanks :)
by Drift99
Mon Nov 26, 2012 4:13 pm
Forum: KA-T Tech. Basic
Topic: 12 point bolt in block. What size is it?
Replies: 7
Views: 1263

12 point bolt in block. What size is it?

Can anyone tell me what size the 12 point bolt is thats in the block? Its holding a little tube (to squirt oil?) just under the cylinder preventing me from pulling the pistons out the bottom.. Anyone know what size it is?

Jake
by Drift99
Thu Oct 11, 2012 2:41 pm
Forum: KA-T Tech. Basic
Topic: Rubber oil lines.
Replies: 4
Views: 1282

im running a BM t25 and have used rubber for my feed and. Its a bad idea. The rubber gets hard after a few heat cycles and cracks. Its ok for a temporary fix but dont run it for more then 3 weeks.. This is what happen to me at the track running rubber feed http://imageshack.us/a/img404/6862/aug6thdr...
by Drift99
Sat Aug 04, 2012 12:12 pm
Forum: KA-T Tech. Advanced
Topic: 248/248 Cam on Turbo Setup
Replies: 28
Views: 5677

Thanks guys I did the 3 tooth instead of 4 because I thought it sounded way meaner. I ended up putting the stock cam back in for now. My engine always had a bit of a fluctuating idle and with the 248 in there, the fluctuation got pretty bad. The engine would die on me and just ran really rough with ...
by Drift99
Wed Aug 01, 2012 4:23 pm
Forum: KA-T Tech. Basic
Topic: How do you clean the stock injectors?
Replies: 5
Views: 1173

you gotta be careful what chemicals you use or you will destroy the windings . Best way is to run a mixture of pressurized gasoline with gm top end cleaner mixed in while the engine is running . I have a pressurized system I use Do you have a pic of the system? Im trying to think of how you can run...
by Drift99
Tue Jul 31, 2012 2:25 pm
Forum: KA-T Tech. Basic
Topic: How do you clean the stock injectors?
Replies: 5
Views: 1173

How do you clean the stock injectors?

I have searched and haven't found an answer. How cam I clean out my injectors? I was thinking of dunking them in carb cleaner. Its for my DD so I cant be sending them off in the mail. Thanks,
Jake
by Drift99
Tue Jul 31, 2012 2:20 pm
Forum: KA-T Tech. Advanced
Topic: 248/248 Cam on Turbo Setup
Replies: 28
Views: 5677

There is a link to the video above your reply :D .

My car is having problems holding a steady idle. The problem got worse after I put this cam in. Im pretty sure its because of clogged injectors. If anyone knows how to clean our stock injectors plz let me know.
by Drift99
Mon Jul 30, 2012 7:41 pm
Forum: KA-T Tech. Advanced
Topic: 248/248 Cam on Turbo Setup
Replies: 28
Views: 5677

Alright guys I figured out what I messed up on :x . I rushed the distributor install (it was like 2am and I wanted to hear the thing idle already). I installed the distributor one tooth over :oops: . I fixed that and she fired up no problem. The car was idling lean around 17.5 so I had to increase t...
by Drift99
Sun Jul 29, 2012 6:40 pm
Forum: KA-T Tech. Advanced
Topic: 248/248 Cam on Turbo Setup
Replies: 28
Views: 5677

Thanks for the reply.

I guess the cam must be bent then. I dont seen any other reason why it would be locking up when I crank it. :x