Search found 83 matches

by 2hunglow1standhi
Tue Dec 09, 2014 8:29 pm
Forum: KA-T Tech. Basic
Topic: frontier goes into limp mode at 4k
Replies: 5
Views: 1902

Re: frontier goes into limp mode at 4k

And finally check for boost leaks... 13.5 is way too lean in boost. That FMU should be richening it up to about 11-10AFR's @7psi. Rich but safer then 13...
by 2hunglow1standhi
Tue Dec 09, 2014 8:27 pm
Forum: KA-T Tech. Basic
Topic: frontier goes into limp mode at 4k
Replies: 5
Views: 1902

Re: frontier goes into limp mode at 4k

Get a obd2 scaner and see if the MAF is tripping a code. The MAF setting for a Z32 MAF is 2 in.. Frontiers run a 5 out. Voltage from the Z32 should be 0.45volts or so.. The AFC should double the voltage back to the ECU with a 2in 5out.. 0.80 volts or so. Thats how it is for mine. Then tune it back t...
by 2hunglow1standhi
Tue Dec 09, 2014 12:58 pm
Forum: SOHC KA-T
Topic: Ka24et Build for my 510.
Replies: 7
Views: 3553

Re: Ka24et Build for my 510.

Fantastic beautiful build!
by 2hunglow1standhi
Tue Dec 09, 2014 12:46 pm
Forum: KA-T Tech. Basic
Topic: frontier goes into limp mode at 4k
Replies: 5
Views: 1902

Re: frontier goes into limp mode at 4k

Ok, most here will tell you to get injectors and a real tuning solution.... However, do you know for sure its in limp mode? Frontiers have many limp modes, one for bad MAF signal (around 3500RPM), and knock detection (timing), then closed to open loop issues with the (O2 sensor). Your problem seems ...
by 2hunglow1standhi
Fri Sep 19, 2014 2:34 am
Forum: KA-T Chat
Topic: KA-T loses power when boost hits
Replies: 9
Views: 3376

Re: KA-T loses power when boost hits

Go tru the normal checks. Timing, boost leaks, what did Enthalpy say?

Strange your able to build 8 psi revving "parked"?

And are you Blow through? Or suck through?
by 2hunglow1standhi
Sat Sep 13, 2014 2:50 am
Forum: KA-T Tech. Basic
Topic: 350ish HP from a DE setup
Replies: 7
Views: 2638

Re: 350ish HP from a DE setup

How many miles you have on that motor? Just wondering cause you didn't list any oil/water pumps, or timing components. Just checking...
by 2hunglow1standhi
Sun Jul 27, 2014 2:15 pm
Forum: KA-T Tech. Basic
Topic: Throttle Body Shaft Seal
Replies: 10
Views: 4452

Re: Throttle Body Shaft Seal

If they are the same size I do not know. Would be very nice if it were. Double lip seal Q45 TB would be sweet!!!!
by 2hunglow1standhi
Mon Apr 28, 2014 2:26 am
Forum: Chat
Topic: Favorite SNES Vidoe Games
Replies: 16
Views: 9905

Re: Favorite SNES Vidoe Games

How many of you out there still own a perfect working NES, or SNES? And still play it? Lol! Just wondering...
by 2hunglow1standhi
Mon Apr 28, 2014 2:11 am
Forum: KA-T Tech. Basic
Topic: S14: 17x9 up front, 18x10 in the rear
Replies: 9
Views: 2318

Re: S14: 17x9 up front, 18x10 in the rear

14x10 gangsta 100 spoke Daytons! Knock offs, and white walls! Lol! Chrome fender trim! Lol! Huge double blade wipers! Limo TV antennas! All on a 1990 240sx..... Sometimes change is good! Haha!
by 2hunglow1standhi
Mon Apr 28, 2014 2:05 am
Forum: KA-T Tech. Basic
Topic: leaking injector w/no pressure
Replies: 4
Views: 1313

Re: leaking injector w/no pressure

Thats just how it is, stuck open, or something blocking it from closing. Fuel in the rail, hoses, its gotta go somewhere of least resistance. Even if it was not under pressure, the vapor always builds some pressure...
by 2hunglow1standhi
Mon Apr 28, 2014 1:58 am
Forum: KA-T Chat
Topic: wide band readings
Replies: 9
Views: 2276

Re: wide band readings

Nice to hear everything is going good man. If Martin is helping you? Then you are in good hands.
by 2hunglow1standhi
Sun Apr 20, 2014 4:05 pm
Forum: SOHC KA-T
Topic: Fuel rail and intake manifold dimensions
Replies: 4
Views: 2436

Re: Fuel rail and intake manifold dimensions

I would mod some brackets, or as Beercan would say, Homebrew!
by 2hunglow1standhi
Sun Apr 20, 2014 3:36 pm
Forum: SOHC KA-T
Topic: Fuel rail and intake manifold dimensions
Replies: 4
Views: 2436

Re: Fuel rail and intake manifold dimensions

For most 14mm injectors to fit SOHC stock fuel rail they will need to be machined down to 11mm. Or get one of those 14mm Beercan fuel rails! The 14mm injectors, depending on pintle type may or may not fit the stock intake manifold, but there are a lot that can and just use the OEM injector insulator...
by 2hunglow1standhi
Sat Apr 19, 2014 6:11 am
Forum: KA-T Chat
Topic: add this up guys
Replies: 6
Views: 1712

Re: add this up guys

Forms are a special type of community. Each one has its own rules and policy. I am sure no one is really scolding you, just giving the advice and structure. Take it as a helpful reply from one of the top members. Heck you may even become best buds one day. To add to your post? We all have had a bunc...
by 2hunglow1standhi
Mon Apr 14, 2014 12:43 pm
Forum: KA-T Chat
Topic: where have they gone!!!!!!!!
Replies: 15
Views: 4201

Re: where have they gone!!!!!!!!

All my builds was hardcore credit, or eat cup-o-noodles!
by 2hunglow1standhi
Mon Apr 14, 2014 12:38 pm
Forum: KA-T Chat
Topic: got my turbo on, but check this out
Replies: 5
Views: 1396

Re: got my turbo on, but check this out

Or that dang mani gasket! Lol! Wait till the TB starts to leak! Thats fun also!
by 2hunglow1standhi
Mon Apr 14, 2014 3:23 am
Forum: KA-T Tech. Basic
Topic: New to KA-T
Replies: 4
Views: 1445

Re: New to KA-T

Was it in bad condition when you first bought it? Did you check for any signs of engine problems? Comp check? Oil check? Smoking or leaks? How are the injector seals and insulators? Boost leak test yet? plugs? For the rad fans controller, The autoparts store one's work alright... $40, adj 165-190 de...
by 2hunglow1standhi
Sat Apr 12, 2014 1:19 pm
Forum: KA-T Chat
Topic: exhaust fittment
Replies: 2
Views: 1129

Re: exhaust fittment

All S13 SR/KA catback exhausts are made to bolt to the OEM location cat converter/testpipe. As long as your turbo set up, top mount or bottom mount, bolts fine to the factory cat/testpipe location? Any brand SR/KA catback is good to go!
by 2hunglow1standhi
Thu Apr 10, 2014 9:49 pm
Forum: KA-T Chat
Topic: where have they gone!!!!!!!!
Replies: 15
Views: 4201

Re: where have they gone!!!!!!!!

I am wondering how many KA-T 240's on this forum was built on "Baller", (credit card), IOU, budgets now????? Lol!
by 2hunglow1standhi
Sat Mar 29, 2014 2:00 am
Forum: SOHC KA-T
Topic: Non turbo'd but removed egr....butterfly valve question
Replies: 5
Views: 3426

Re: Non turbo'd but removed egr....butterfly valve question

I pretty sure the butterfly/ Swirl control valves are always open until they get vac... Just leave the vac hose unplugged. Nothing bad will happen either way. Most say you will loose low end... But the "butt" Dyno didnt feel any loss. You could even unplug the harness connector on the SCV,...
by 2hunglow1standhi
Thu Feb 20, 2014 9:39 am
Forum: SOHC KA-T
Topic: ka24e-t Build suddenly not running.
Replies: 2
Views: 1958

Re: ka24e-t Build suddenly not running.

Ok so, you rebuilt the motor, it drove / boosted fine for a day, turned car off, then the next start it cranked only? When it is sputtering and trying to idle? Whats the AFR's? Lean or rich? Does the ECU red light switch off? Does it flash any codes? Did you look inside the ECU to see if the chip wa...
by 2hunglow1standhi
Fri Jan 24, 2014 10:17 am
Forum: KA-T Tech. Basic
Topic: Help!! Altima oil return question
Replies: 5
Views: 1390

Re: Help!! Altima oil return question

Are you running a oil inlet restrictor? What weight oil do you run? -10 for a drain is good. Other then the pan, some Honda friends drill and tap the bottom of the block. Is the return a straight shot down from the turbo? What brand of rebuild kit did you use? Most guys rebuild using Genuine Garret ...
by 2hunglow1standhi
Wed Jan 22, 2014 8:38 am
Forum: SOHC KA-T
Topic: SOHC engine, DOHC ECU questions?
Replies: 2
Views: 2015

Re: SOHC engine, DOHC ECU questions?

Ok cool! Thanks.
by 2hunglow1standhi
Tue Jan 21, 2014 10:33 am
Forum: SOHC KA-T
Topic: SOHC engine, DOHC ECU questions?
Replies: 2
Views: 2015

SOHC engine, DOHC ECU questions?

Alright, for those people running Jim Wolfs DOHC ECU / Distributor re-clock, for the SOHC engine program, or know someone who has, or, anyone running a DOHC ECU with a SOHC engine, question for you. Did you have to swap over to a DOHC tach? As we all know, the two engines/ECU's use different tach's ...
by 2hunglow1standhi
Sat Jan 11, 2014 7:55 pm
Forum: KA-T Tech. Basic
Topic: ka-t wont run
Replies: 14
Views: 3305

Re: ka-t wont run

If the MAF power wire and signal wire on the harness is not giving the 12v power or 0-5volts signal, then open up your ECU and look for burnt traces, or any burnt pins... Lot of the times the MAF can handle the short circuit and it sure soundls like it will be fine, but the ECU might be fried now..
by 2hunglow1standhi
Sat Jan 11, 2014 4:24 am
Forum: SOHC KA-T
Topic: My build. Nissan AXXESS awd 5spd
Replies: 16
Views: 5804

Re: My build. Nissan AXXESS awd 5spd

Man! This is going to be good!
by 2hunglow1standhi
Sat Jan 11, 2014 4:21 am
Forum: Car Chat
Topic: 2015 Mustang 4 banger turbo
Replies: 1
Views: 2221

Re: 2015 Mustang 4 banger turbo

Looks promising... Gotta love Napoleon syndrome! Especially when its your choice!
by 2hunglow1standhi
Sat Jan 11, 2014 4:11 am
Forum: KA-T Tech. Basic
Topic: Throttle Body Shaft Seal
Replies: 10
Views: 4452

Re: Throttle Body Shaft Seal

On another note? My backup KA-E TB, I am planning to send out to Maxbore .com, he may be able to repair it, he has access to a bunch of different seals and is willing to give it a shot. I just needed a quick fix cure and researched my butt off on the subject....
by 2hunglow1standhi
Sat Jan 11, 2014 4:04 am
Forum: KA-T Tech. Basic
Topic: Throttle Body Shaft Seal
Replies: 10
Views: 4452

Re: Throttle Body Shaft Seal

Grease fix finally gave out after all this time... Ok, here it is people, Nissan turbo engines have a different type of throttle body shaft seal then N/A engines! Its a double lip design made for vacuum..... "AND", positive pressures! Any SR20DET, CA18DET, VG30DETT, RB20DET throttle body h...
by 2hunglow1standhi
Mon Jan 06, 2014 2:19 am
Forum: KA-T Tech. Basic
Topic: ka-t wont run
Replies: 14
Views: 3305

Re: ka-t wont run

New? Z32 maf? As in $$$ from Nissan oem? Or a aftermarket new MAF? Some aftermarket MAF's are funky. But yeah, once in a while its the tune... On some cars, and ECU's, tunes are just finicky. Are you able to get the car to the tuner? And dyno tune it? Most tuners have seen it all when it comes to pr...