www.ka-t.org

O.M.G. Billy, how are you, hows your project!???)))) anywhay this Revhard is one guy, not a team, meet him in person, very very nice guy! His garage is a dream!))) heres what hi did to another weak GTR spot, i bet its much much better than any aftermarket clutch pivot bolt now! Its unbrakable!))) ht...

i do have a crank collar, laying under the bed, but im not reach enough to pay for a machinig! and the topic was asking not about solution of this problem, it was about which weld is the strongest toughest one!!) I have 2 amazing welder budys, who can weld beyond limits, both of them are the gods of...

i do have a crank collar, laying under the bed, but im not reach enough to pay for a machinig! and the topic was asking not about solution of this problem, it was about which weld is the strongest toughest one!!) I have 2 amazing welder budys, who can weld beyond limits, both of them are the gods of...

Im not going to weld it myself! Im going to go to a weld shop but i need to know which weld (ROD?) to reqest!?

HI, i am working on the RB26 motor which has a steel stock cranck (so could be welded on i assume) As many of us know RB and especially 26's has a huge oil pump drive collar issue, where oil pump got broken or collar on the cranck is getting stripped! In my case oil pump gear got cracked on one side...

Ok ive been looking for one for a while now, so I found them only in 2 places if you know more please add. So which one you would recommend to go with between this 2???? http://straightlinespecialties.com/shop/product_info.php?cPath=29_35_53&products_id=40 or http://www.bmcrace.com/product_info....

me too!

Hi yes besides Xcessive, where can i find an 24DE exhaust flange and if you got it from somebody youll recommend how was the qality of it?

Been done with gread results!

http://www.dsmtuners.com/forums/turbo-s ... y-car.html

http://www.carvideosonline.com/dsm-vide ... he351.html

did anyone used WISECO headgasket before? Hows the results?

Yes im running maf on the cold pipe but im FWD, running about 20psi on build block! Did you ever check for boost leaks? on20 psi if your maf is not glued to the rubber coupler in some whay will leak, you can tight it down untill you brake plastic on maf! Well theoreticly its not POPPED OFF, it just ...

I have like 4 N62 one of them went dead because of the top cover keep popping even JB weld didn't take it i used urethane and that when it went out! Next one i jb weld from inside around the sensor element and that hole as well let you guys know about that! Bottom is my JB weld set up it broke one l...

You guys mind post some specs like what pistons/rods/bearing/headgasket?
Or somebody can provide a link for me?

So what managment are you running?

Waiting forsome pics, i have similar set up so couple of qestions:

1- What Ex a/r on the turbine (Twin scrol?!)
2 - What camshafts? (who degreed them?)
3 - What management?
4? - Timing set at?

Iam sorry guy i didn't read the whole thing but i have a link for you who might be intrested!

F1 Technology

http://www.f1technical.net/forum/viewto ... f=4&t=3012

So for about half a year i coudnt find decent guy who could of done this (JUST THE TOP PART (PLENUM???)), this is my first intake with my buddy welder I USED 3.5" diametre piping 1 90 degree, 1 45 degree and a little extension! http://i151.photobucket.com/albums/s124/tryingtobebest/White/Intake...

Finally after 2 of them i got the right lenght and the proper angle of the plate! So anybody want to help me finish this? I need 3.5" thick upper plenum anybody! http://i151.photobucket.com/albums/s124/tryingtobebest/White/Intakepart1002.jpg http://i151.photobucket.com/albums/s124/tryingtobebes...

snap...

ok, searching on the forums about injectors i found that not all top feeds are the same but most of them are 60mm in lenght (not shure please confirm) Is that what AMS fuel rail is made on? And one moer qestion: I heard alot of good stuff about NEW 1000cc Bosch injectors, anybody who migh read this ...

How much will you charge for that? Because like i asked in pm i have good friend which is welder! and he can weld them for free for me! All i need is 2 pipes - 90degree and 45???? long piece! BUT again don't know what diameter im gussing it is 3.5"! Besides im not shure which TB im going to use...

I don't know how critical is the second port on the 240 intake flange but i don't think its very critical, here is how 240 and Altima gaskets looks like side by side courtesy of xcessive manufacturing http://i151.photobucket.com/albums/s124/tryingtobebest/Engine%20rebuild/BOTH.jpg And one more thing...

O&Jperformance you got a pm, please help!

You should check better guy, slappynuts is very good custom fabricator and he is doing us (FWD) guys a favour by makind somthing like this! Im shure hi got lots of 240 flanges!

Yes if it going to come out perfectly straight (not angeled towards the passenger fender on 240) Because on Altima its better to have it angeled towards other side (dr fender)
Looking forward to see what your going to get!

Xcessive manufacturing has gaskets between upper intake and head side by side, check them out they are a bit different between Altima and for 240 so as the uppper plenum!

http://www.xcessivemanufacturing.com/me ... =16&step=2

I ve contacted them about not wlded bare plenum (see my qestion earlier in this thread) and they been tooo cheap to make one for me!
No go again for my FWD KA![/list]

Beinga an Altima fan, i am woundering how much would BARE plenum cost i have a nice local welder who can weld it together so i am asking how much is for plate that welds to runners and a plenum itself, no TB adapter or TB reducer needed! Please can you check!? http://i151.photobucket.com/albums/s124...

nice set up, mind posting any pictures of intake/ex mani?

Which CAMS, how are they set, what ecu!

any other ideas?