Search found 571 matches

by DrEaMeR_VaNg
Wed Jan 11, 2017 12:35 pm
Forum: KA-T Chat
Topic: I got the boot.
Replies: 12
Views: 4794

Re: I got the boot.

Ked,

do you still have your KA-T???

It's great to see some of the older members still come around once in awhile.
by DrEaMeR_VaNg
Tue Apr 26, 2016 4:00 am
Forum: KA-T Chat
Topic: new z33 adapter plate
Replies: 4
Views: 2479

Re: new z33 adapter plate

I posted this in the group buy topic..

What else other than the transmission is needed for this swap? What rear end is needed to match the Z33 6spd & gearing?

Anyone got answers?
by DrEaMeR_VaNg
Fri Mar 04, 2016 7:06 am
Forum: KA-T Tech. Basic
Topic: Tightening crank pulley
Replies: 3
Views: 1695

Tightening crank pulley

So this is a really noob question but how do you tighten the crank pulley? I bought a motor and that bolt is loose (supposedly it was a good motor but now I'm thinking it's a bad motor because the bolt is loose). The motor is out of the car. Could I tighten the crank pulley by chaining the flywheel ...
by DrEaMeR_VaNg
Fri Oct 16, 2015 11:55 am
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

The car is still sitting and I can't figure out what's wrong with it. Finally broke one of the distributor bolts into the head so gonna have to remove that before I can work on it again. I am thinking about changing the motor and hope that it starts.. For some reason I could never align the distribu...
by DrEaMeR_VaNg
Wed Jun 10, 2015 8:12 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

I believe my distributor timing is off therefore the motor turns over and stops then turns over again? :\ Tested the TPS and I'm getting 5v on terminal 1 with ignition on, and I have continuity between terminal 3 and ground. Ohms are reading correct at completely closed, partial, and open. If everyt...
by DrEaMeR_VaNg
Mon Jun 01, 2015 7:27 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

. yes it would. I had a knock-off turbo xs bov and the valve leaked under idle ( not to mention it was not recirculated; just vented to atmosphere ). At the time I was also using a z32 MAF. The engine ran pretty terrible and one had to rev it when coming to a stop to prevent stalling... I mean the ...
by DrEaMeR_VaNg
Wed May 27, 2015 9:55 pm
Forum: KA-T Picture Threads
Topic: Duron's $$$ at Work
Replies: 49
Views: 16898

Re: Duron's $$$ at Work

I'm glad to see the OG guys on this topic!

I need to get my KA-T running. :(

Nonetheless I'm looking forward to the progress!
by DrEaMeR_VaNg
Wed Apr 22, 2015 6:05 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

The car starts up fine and idles fine but when I press the gas pedal or pull on the throttle (inside engine bay) the BOV goes off and the car backfires/exhaust makes popping noises. Wait... when you press the gas pedal the BOV goes off? What kind of BOV is installed? . Greddy Type S. I know their k...
by DrEaMeR_VaNg
Tue Apr 21, 2015 3:18 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

This is all that I've done since last August when it went down. Replaced fuel filter Enthalphy sent me a new ECU with a new chip with the same tune Changed fuel rail Changed engine wiring harness Changed distributor/spark plug/spark plug wires/distributor cap Changed fuel pump Replaced OEM FPR with ...
by DrEaMeR_VaNg
Tue Apr 21, 2015 1:22 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

This is all that I've done since last August when it went down. Replaced fuel filter Enthalphy sent me a new ECU with a new chip with the same tune Changed fuel rail Changed engine wiring harness Changed distributor/spark plug/spark plug wires/distributor cap Changed fuel pump Replaced OEM FPR with ...
by DrEaMeR_VaNg
Sun Mar 01, 2015 8:35 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

. So timing was checked and fuel pressure seems to be present (even if its not the "target" pressure). Will the engine start? When the 750cc injectors were swapped over, were the injector "O" rings replaced? A boost leak test may help clear up the bogging issue too, if fuel is f...
by DrEaMeR_VaNg
Sat Feb 28, 2015 8:39 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

The weather has been bad lately so I haven't gotten a chance to work on the car; not having a garage sucks. So the first two times I rented the fuel pressure tester before I swapped the bad FPR out the key on PRIME didn't show anything and even when the car was on and running it read nothing on the ...
by DrEaMeR_VaNg
Wed Jan 28, 2015 2:56 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

I've been caught up and haven't had any time to work on the car since the last time I tried. I had the Quest alternator upgrade before the car went down. I took the advice here and removed it and took it to test at Advance Auto and it was good so I ruled that out. The battery is fully charged.. I al...
by DrEaMeR_VaNg
Sun Jul 06, 2014 6:22 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

So I thought maybe the fuel pressure tester gauge was bad so I rented another gauge and it's still not reading anything. Do I have it set up wrong? There are banjo fittings in the kit that I have no idea how to use and two GM/Ford schrader valve fittings. I use the T looking fitting and hook up the ...
by DrEaMeR_VaNg
Fri Jul 04, 2014 6:27 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

How long ago was the engine touched? Long shot, but idler pulley bolt stripped? If your are getting spark and fuel, timing issue most likely. Also, double check compression. Oh man, this can be quite the headache if you don't know what's going on! When mine stripped, I barely made it back home. Car...
by DrEaMeR_VaNg
Fri Jul 04, 2014 6:26 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

I've been so busy I haven't had a chance to work on the car until today. I went to rent a fuel pressure tester from Autozone today and connected it like so: http://i17.photobucket.com/albums/b77/PaOie-VaJ/fuelgauge_zpsce533996.jpg From the fuel filter it goes to one end of the T rod that goes to the...
by DrEaMeR_VaNg
Wed Jun 25, 2014 5:30 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

Try a known-good battery? Sounds trivial but if it's not charged enough to begin with, cars don't always behave right. Had a Jeep that wouldn't stay running. Jumping it off it would start, but even while jumpered off it would not stay running without feathering the gas. Once I replaced the battery ...
by DrEaMeR_VaNg
Wed Jun 25, 2014 5:27 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

Re: HELP?

check for distributor alignment, if you have the valve cover off you can shine a light down the front cover and when you have it timed properly there will be a mark on the gear and on the distributor housing that line up WHEN THE DISTRIBUTOR IS FULLY PUSHED IN it must be fully in as the gear turns ...
by DrEaMeR_VaNg
Mon Jun 23, 2014 5:36 pm
Forum: KA-T Tech. Basic
Topic: HELP?
Replies: 29
Views: 6369

HELP?

*Mods if this is in the wrong section please move to correct section wasn't sure which section to post this in* Hey guys, so I threw my old kit on my new 240sx. Relocated battery to trunk. It ran fine for a few days then one night coming home it just shut off and wouldn't start up so I had to tow it...
by DrEaMeR_VaNg
Thu Feb 07, 2013 5:35 pm
Forum: DIYAutoTune
Topic: Heads up, we lined up a '96 test car...
Replies: 62
Views: 10935

Sweet. Thanks for the clarification Matt. Next on the list mitchell is the DIY boost control solenoid. I am going to get one soon. Complete control over when the WG opens is sweet. This will help reduce lag a bit since I am running of off WG spring. Lol already in route. Im trying to sell my profec...
by DrEaMeR_VaNg
Tue Mar 20, 2012 7:38 pm
Forum: KA-T Chat
Topic: BC 272/272 + build head
Replies: 5
Views: 1376

Someone is back from hell.

I haven't seen you on this forum for ages. Thought you moved on to other things like the rest of the Gville guys.

Good to see your still here.

Sorry no input to this thread. :(
by DrEaMeR_VaNg
Wed Mar 07, 2012 11:02 am
Forum: Dyno Results
Topic: First KA-T Dyno ever...
Replies: 11
Views: 5183

Congrats!

Great #'s for 6psi! :)
by DrEaMeR_VaNg
Tue Feb 21, 2012 11:29 am
Forum: KA-T Chat
Topic: JGS rubber motor mounts....separating
Replies: 16
Views: 3816

Sorry to hear about your mounts.

I'm sure JGS will take care of you, and if not then you can just buy them from NAPA! :)

I've had mines for over 2 years or so and they are great. Perfect for a DD.
by DrEaMeR_VaNg
Thu Feb 02, 2012 6:04 pm
Forum: KA-T Chat
Topic: People that know how to degree cams, evaluate my video
Replies: 9
Views: 2026

This seems like such a hard job to tackle. Good job nonetheless.

All the guys who were into these kind of things are long gone out of the KA game I suppose that is why there is no feeback to your video.. :(
by DrEaMeR_VaNg
Wed Jan 11, 2012 6:41 pm
Forum: KA-T Chat
Topic: what type of injectors to run on my ka-t
Replies: 19
Views: 3619

I have FiveO 750's. They are basically like DW.

I haven't had a problem with them and I've had them for a year.

I'm not sure if buying directly from FiveO is cheaper but Enjuku out in FL is a vendor for these injector and that's where I got em' from.

Good luck!
by DrEaMeR_VaNg
Thu Jan 05, 2012 10:03 pm
Forum: KA-T Chat
Topic: where can i find some silucone ocouplers?
Replies: 9
Views: 1912

Hey shift,

I've order from www.siliconeintakes.com a few times. You should try them out. I've only had good experience with them.

Good luck and happy boosting!
by DrEaMeR_VaNg
Sun Nov 20, 2011 10:30 pm
Forum: KA-T Picture Threads
Topic: *Post Your Engine Bay Pics*
Replies: 922
Views: 417739

Image

I need a plate or something to cover my brake MC...
by DrEaMeR_VaNg
Sun Nov 13, 2011 9:49 pm
Forum: KA-T Tech. Basic
Topic: Multiple Holset Questions.
Replies: 82
Views: 14930

Re: Multiple Holset Questions.

The compressor housing (intake to maf) is huge and I would love if someone would chime in what size coupler they used (HE341) and the size for the 90 degree bend to the IC piping? I measured the OD's of both but want to make sure I buy the right size couplers. Sorry to bring up and old thread but a...
by DrEaMeR_VaNg
Thu Oct 06, 2011 8:21 am
Forum: KA-T Picture Threads
Topic: S14 PICS only .... :-D must have pics in every post!!!
Replies: 519
Views: 206332

Tried on the VIS lip.

Image

Anyone interested in a VIS lip that is local? :)
by DrEaMeR_VaNg
Wed Sep 28, 2011 12:15 pm
Forum: Dyno Results
Topic: 404hp @23psi tuned with DSM ECU(Video)
Replies: 7
Views: 3945

Congrats on the power! I bet that bad boy pulls hard!