Search found 822 matches

by Berserker
Sun Jul 14, 2013 7:15 pm
Forum: Introductions
Topic: guy from chicago
Replies: 10
Views: 3296

Re: guy from chicago

Haha yeah for sure^^

We should have a meet end of summer.
by Berserker
Sat Jul 13, 2013 5:04 am
Forum: Introductions
Topic: guy from chicago
Replies: 10
Views: 3296

Re: guy from chicago

Welcome back.
by Berserker
Mon Jun 17, 2013 12:22 pm
Forum: KA-T Chat
Topic: Ka24de extreme revs?
Replies: 20
Views: 5607

I tried revving to 6.5k stock cams 50 trim turbo at the track.
Once I reved it to 7k gained 4-6 mph trap speed and better 1/4 mile time
by Berserker
Mon May 27, 2013 4:13 am
Forum: KA-T Tech. Basic
Topic: Fresh rebuild cooling issues
Replies: 12
Views: 2793

I ussually just lift the front up fill her up while having the heat on, Untill it starts pouring out of the bleeder screw. Then start the car while front is lifted up, radiator cap off let it run till heat blows hot inside the car, put the cap back on go for a drive. Easiest fix for me driving last ...
by Berserker
Mon May 20, 2013 5:08 pm
Forum: Dyno Results
Topic: First dyno disappointment...
Replies: 44
Views: 13442

Just to throw it out there on my 50 trim I made 379 whp on dyno dynamic on 17-18 psi.
by Berserker
Fri May 17, 2013 12:48 pm
Forum: Dyno Results
Topic: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35
Replies: 28
Views: 13143

Yeah I had same issue when I leaned out. I threw in new felpro headgasket with 10mm arp headbolts resurfaced head and ran that motor 21 psi 400whp on 50 trim(e85 stock block) for a while before I build this current motor. Sold that motor with excelent compression.
by Berserker
Thu May 16, 2013 7:47 am
Forum: Dyno Results
Topic: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35
Replies: 28
Views: 13143

http://www.ka-t.org/karey_d.php

He ran 700 whp with 10mm arp head studs. I think miami240 said its all in the tune.
by Berserker
Thu May 02, 2013 5:55 pm
Forum: Introductions
Topic: Chicago, chicago...
Replies: 8
Views: 2627

Welcome! I'm from Chicago as well :)
by Berserker
Tue Apr 30, 2013 4:13 am
Forum: Car Chat
Topic: any vh45de users here?
Replies: 18
Views: 6563

Lol I bought a donor q45 with a broken transmission for 600, now justntrying to figure out where to swap in lol.
More people need to do these swaps in order to gain aftermarket support.
by Berserker
Sat Apr 20, 2013 1:45 pm
Forum: SOHC KA-T
Topic: Project KA24E(T)!!! NEW BUILD PAGE
Replies: 462
Views: 213561

Might have to call and confirm if will actually hold that much tq. When I brake this one I'm going to have to go bigger as well. twin disk very expensive.
by Berserker
Sat Apr 20, 2013 4:40 am
Forum: SOHC KA-T
Topic: Project KA24E(T)!!! NEW BUILD PAGE
Replies: 462
Views: 213561

I made 520ish tq, cant remember of the top of my head, but it was around there. Its a z32 clutch. It worked with my KA trans, ripped the gears. Now I have a z32 trans in there and it still works with that as well. But I have not tested out on that power hard launches on the track with slicks. I will...
by Berserker
Fri Apr 19, 2013 9:09 pm
Forum: SOHC KA-T
Topic: Project KA24E(T)!!! NEW BUILD PAGE
Replies: 462
Views: 213561

Well it depends whats your budged and how much you want to spend.
If you can just buy a twin disk deff go for it.

I'm on white bunny 6 puck. 608 whp and it holds. That would be the cheaper alternative. A lot cheaper.
by Berserker
Sun Apr 14, 2013 7:07 am
Forum: Drag Racing
Topic: 11.3 second pass VIDEO!
Replies: 32
Views: 8573

Haha great launch. I don't think my white bunny clutch would really enjoy a launch like that lol
by Berserker
Sun Apr 07, 2013 8:11 pm
Forum: KA-T Chat
Topic: Fel pro head gasket limit 10mm studs
Replies: 20
Views: 3614

I have a cosworth gasket in right now with new 11mm arp studs.
I had my head resurfaced again.
For the block I cleaned up and used a block sander to smooth it out. It was decked when I had machine work done.
So far so good.
by Berserker
Sun Apr 07, 2013 5:03 pm
Forum: KA-T Chat
Topic: Fel pro head gasket limit 10mm studs
Replies: 20
Views: 3614

Yeah I also have the same turbo and I made 490whp @ 20 psi if I remember correctly. And it was not aggressive timing at all.
by Berserker
Sun Apr 07, 2013 2:36 pm
Forum: KA-T Chat
Topic: Fel pro head gasket limit 10mm studs
Replies: 20
Views: 3614

My 500whp held for few summers, and I beat on the car alot. But once I went over 600 it started leaking. But I'm also on 11mm head bolts. I also leaned out few pulls on the highway with felpro(1 fuel pump burned out) but put in new pump and still finished the summer without any problems. If you have...
by Berserker
Sun Apr 07, 2013 8:16 am
Forum: KA-T Chat
Topic: Turbo Selection poll/thoughts 450-500hp
Replies: 9
Views: 2405

6 puck white bunny clutch will hold 500whp easily, and That's 375$
by Berserker
Sun Apr 07, 2013 7:49 am
Forum: KA-T Tech. Basic
Topic: What Bearings 500+HP
Replies: 16
Views: 2760

I'm using clevite as well 600+
by Berserker
Fri Apr 05, 2013 8:00 am
Forum: KA-T Tech. Basic
Topic: dual cam w/o power steering belt
Replies: 8
Views: 2225

Single belt from autozone, tight fit but got it on had it for 3 years or so.
by Berserker
Sun Mar 31, 2013 9:37 am
Forum: KA-T Picture Threads
Topic: 01 maxima coils
Replies: 7
Views: 2539

Don't you wantnbto gap them down take it on the highway see how it pulls, if it holds?
by Berserker
Fri Mar 29, 2013 7:36 pm
Forum: KA-T Tech. Basic
Topic: z32 tranny
Replies: 4
Views: 1410

lol that just sounds unhealthy .

Il have to verify everything again, because that free rev vibration is annoying as hell.
by Berserker
Fri Mar 29, 2013 12:59 pm
Forum: KA-T Tech. Basic
Topic: z32 tranny
Replies: 4
Views: 1410

z32 tranny

Hey I had a question for the guys that are running z32 manual trany.
My shifter vibrates crazy, mad noise coming from there. Using mazworx adapter. If I free rev it past like 4k mad vibration to redline lol any1 else gets this?
Drives and shifts good.
by Berserker
Thu Mar 28, 2013 4:46 am
Forum: KA-T Tech. Basic
Topic: Should I buy this setup for just under $600?
Replies: 8
Views: 2125

Its not bad if its welded to the downpipe. Just the t25 is hella 2 small, adleast a t28 would be nice. But its not a bad price.
by Berserker
Wed Mar 27, 2013 3:29 pm
Forum: KA-T Tech. Basic
Topic: Should I buy this setup for just under $600?
Replies: 8
Views: 2125

I never regret starting out small, my fist dyno I put down 270whp on sr t28 turbo. It was alot of fun makes you want to upgrade. So I cept on adding more parts. Learned alot that way. Ibwould recomend getting a bottom mount set up but just not turbo welded on manifold.
by Berserker
Wed Mar 27, 2013 4:33 am
Forum: KA-T Picture Threads
Topic: 01 maxima coils
Replies: 7
Views: 2539

Dyno them for 700whp to see if they hold. :) Im interested too if they hold well I might switch as well lol
by Berserker
Sun Mar 17, 2013 7:01 pm
Forum: KA-T Tech. Basic
Topic: Maxima coils- Bad experience
Replies: 8
Views: 3063

I also had a few bad coils from the junkyard, but those maximas had 240k+ miles lol other then few bad coils they hold 28 psi 600 whp for me. All my coils are from almost 200k miles maxima :S
by Berserker
Fri Feb 08, 2013 9:38 pm
Forum: KA-T Tech. Advanced
Topic: Cometic HG Failure
Replies: 51
Views: 14434

I ran @ 500 whp @ 25lb for 2 summers with felpro headgasket. Had 11mm arp bolts. I beat on the car alot. Only started leaking passed 600. But also b4 that had 1 fuel pump burn out and leaned out twice @ 20+ psi. That proly helped it leak.
by Berserker
Tue Feb 05, 2013 10:28 am
Forum: KA-T Tech. Basic
Topic: Will a slightly hot ka cause rich?
Replies: 3
Views: 1074

It can if its too hot. Mine just started overheating on a wot pull and wideband was reading 10s and lack of power. Then I waited like 10 mins to cool down then it was normal again.
by Berserker
Tue Feb 05, 2013 10:24 am
Forum: Other Videos
Topic: MEANEST LAUNCH EVER!!!
Replies: 10
Views: 8258

500hpKA240sx wrote:that is crazy... but thats a perfect example of compared vids, thats why i dont want a turbo.. that 2 step just sounds stupid.
Dont know how you can think 2step is stupid, that supra's launch is sick. And it sounds mean as fk.
by Berserker
Tue Feb 05, 2013 2:20 am
Forum: Other Videos
Topic: MEANEST LAUNCH EVER!!!
Replies: 10
Views: 8258