Search found 822 matches

by Berserker
Sat Sep 08, 2012 4:53 pm
Forum: Dyno Results
Topic: New dyno Headgasket bye bye
Replies: 13
Views: 2717

New dyno Headgasket bye bye

Went to the Dyno today finished tuning, everything was fine drove back home, did some pulls on the highway. But then stopped, started driving again noticed it was overheating a bit. Then Pulled over and looked the reserve tank was 3/4 filled, I had this problem before. Headgasket leaking under high ...
by Berserker
Sun Sep 02, 2012 6:00 am
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

Injector duty cycle a little over 70%

Yeah I saw a few post about the Cosworth gasket, I would have to read more into it but it does not sound like a bad deal. And yeah as you mentioned I saw quite a few people running stock head gasket 500+ whp range. That was my goal b4 but now I want more lol.
by Berserker
Sat Sep 01, 2012 6:16 am
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

For now im going to kick it up to 28lb. Once I build head and stronger headgasket ima kick it up to 34 or so.
by Berserker
Wed Aug 29, 2012 6:56 pm
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

Yeah I'm sure he was on the safe side, the shop tunes mostly honda engines. Not a lot of Nissan engines. I tried going to AMS but they said they cant take me too busy. They worked with KA's, I had high hopes there. But 240sx for them are too cheap. They dint tell me they were a month behind or somet...
by Berserker
Wed Aug 29, 2012 5:08 pm
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

PM me who else needed the timing map. Also I wont get a dyno sheet, asked several times and called em and they say they will send it out but nothing. Going back there the September 9th and finish the tune. I will snap a picture of the dyno graph, I did not think it was so hard to pull the dyno sheet...
by Berserker
Tue Aug 21, 2012 6:15 am
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

You cant open s1 map with s2 as far as I know.
Its 63 a/r backside
My tune is on GM 4 bar.map.
by Berserker
Mon Aug 20, 2012 8:12 pm
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

I got my Clutch from here just 6 puck
http://thmotorsports.com/competition_cl ... 20734.aspx

Tomorrow I should be able to get the maps. And my dyno guy wont email me the graph until Thursday, because he is out of state :(
by Berserker
Mon Aug 20, 2012 10:44 am
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

Yeah the intake manifold is stock, wanna see the graph too again.
by Berserker
Mon Aug 20, 2012 2:37 am
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

Wiseco pistons 9.0:1 +.020 Eagle rods Felpro Headgasket with 11mm head studs torqued 86 ft/lb 1600cc precision Dual Walbros JWT S1 Cams Tial 38mm wastegate 6 puck white bunny set up Pm me your email. Once I get a chance to connect laptop I can send you my timing map. I work out of state all week so ...
by Berserker
Sun Aug 19, 2012 6:53 pm
Forum: Dyno Results
Topic: Dyno results
Replies: 21
Views: 3133

Dyno results

Went to the dyno, did not finish the tune but it was close ecu+laptop started acting up. precision 6262 E85 Aem ems series 1 14psi 403whp 19psi 491 whp 24psi 546 whp Waiting for dyno graph to be emailed to me so I will post up when I get it. All and all and I'm happy, but going to get it fined tuned...
by Berserker
Sat Aug 04, 2012 3:33 pm
Forum: Dyno Results
Topic: dyno 11:1 compression (425HP/400TQ at 21psi)
Replies: 17
Views: 4139

Damn that looks like a fun set up for street.
by Berserker
Mon Jun 25, 2012 8:08 pm
Forum: KA-T Picture Threads
Topic: Hector's s14 turbo KA 840hp / 679tq
Replies: 56
Views: 8901

So does any1 know what those coils are?
by Berserker
Sat Jun 23, 2012 8:15 am
Forum: KA-T Picture Threads
Topic: Hector's s14 turbo KA 840hp / 679tq
Replies: 56
Views: 8901

Damn that looks really clean.
by Berserker
Fri Jun 22, 2012 4:41 pm
Forum: KA-T Chat
Topic: Walbro 400 e85 version
Replies: 14
Views: 1293

It should be 700whp rated on E85 right? single pump
by Berserker
Mon Jun 11, 2012 6:22 am
Forum: Car Chat
Topic: Ford day at the dragstrip
Replies: 12
Views: 1328

It's a Ford with a Nissan front conversion
by Berserker
Sun Jun 10, 2012 8:10 pm
Forum: KA-T Picture Threads
Topic: SR20det BMW build in Bangkok Thailand (no ka's in Thailand)
Replies: 24
Views: 5847

lol loving that E30, more pics :) I wanna swap in a ka into 1 now hahah.
by Berserker
Wed Jun 06, 2012 6:15 pm
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

Still acts up on reverse, and If you try to engage the clutch slowly lol
by Berserker
Tue Jun 05, 2012 5:24 am
Forum: KA-T Chat
Topic: 3" dp to 2.5" catback hurt performace alot
Replies: 3
Views: 459

at that power level it wont hurt at all.
by Berserker
Mon Jun 04, 2012 8:13 pm
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

lol today I came back from work and went for a ride, felt so much better, go figure how...fixed it self over night.

Stop to first gear pretty smooth now.
by Berserker
Mon Jun 04, 2012 12:22 pm
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

I have a pretty hard chatter that causes some loud clunking in the rear. I have yet to figure out what it is. I thought maybe it was play between the driveshaft, diff and axles. Good discription what is happening to me. I will have to break it in more and see if it will ease up, its only from stop ...
by Berserker
Mon Jun 04, 2012 9:52 am
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

Yeah I did, I remember the flywheel went in hard ,but I did tighten criss cross. Over the last 2 years iv taken motor out like 3 Times and swapped evrything over each time, and few transmission changes, so its not first time, and always just fallow OEM specs, did not have a problem. Just this time i...
by Berserker
Mon Jun 04, 2012 9:01 am
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

Not yet, ill try to get one up, its kind of like a jerking when I try to start to drive slowly with vibration lol hard to explain, ik have to take a drive and film it, hopefully my flywheel is aligned well.
by Berserker
Sun Jun 03, 2012 8:33 pm
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

Yes everything torqued to spec, no thread locker though, my last clutch was 6 puck as well, less torque rated though, it does not bother me.
Just wanted to see some1 else who installed same set up had same thing happen. We will see if its gonna be smoother with more miles.
by Berserker
Sun Jun 03, 2012 7:32 pm
Forum: KA-T Tech. Basic
Topic: White bunny set up question
Replies: 17
Views: 952

White bunny set up question

Just installed my white bunny set up with 6 puck clutch, and having vibration when start to drive, car shakes till clutch engages, then everything is normal, when shift gear in lower rpms I feel abit of vibration as well. Any1 else had this problem who just installed a new clutch with flywheel. I on...
by Berserker
Tue May 29, 2012 9:24 am
Forum: KA-T Chat
Topic: how much horsepower can the ka diff handle
Replies: 20
Views: 2018

I had welded diff, abused it at the track and on the street, broke while I was cruising home, I had my diff welded by some shop that advertises on zilvia.net can't remember how long it lasted , 2 summers maybe, running j30 now, its got a anoying humming noise , on very light throttle. Guess I was lu...
by Berserker
Thu May 24, 2012 9:26 am
Forum: KA-T Chat
Topic: Precision turbo oil restrictor
Replies: 14
Views: 2206

I'm on 6262 4an feed line no restrictor, not sure how many miles I put on like 2k? I was wondering about that too, I would suggest call precision and ask...
by Berserker
Tue May 15, 2012 8:11 pm
Forum: KA-T Chat
Topic: GSP new to KA-T
Replies: 44
Views: 2310

They getting bigger now, so the prices on their stuff going up, I noticed that, my other question is, is the quality going up?
by Berserker
Tue May 15, 2012 11:25 am
Forum: Car Chat
Topic: is it just me or are ppl asking way to much for their 40's
Replies: 14
Views: 1540

Lol here in chicago anything thats does not have rust, people wanted 3k-4k some of them don't even run.

This one is epic

http://chicago.craigslist.org/nwi/cto/3010858324.html

I would not pay 300, cus there is so much to fix on that char.
by Berserker
Sat May 12, 2012 4:44 pm
Forum: Drag Racing
Topic: Raced last night and didnt do so well :(
Replies: 11
Views: 2075

I'd really like to see what you run on 29 lb. I have almost same turbo 6262, I wanna see what you can trap with 29 lb cus thats how much psi I got it set to now. Although I dont have a z32 trans, so I cant run my car haha :S
by Berserker
Sat May 12, 2012 2:36 pm
Forum: Drag Racing
Topic: Raced last night and didnt do so well :(
Replies: 11
Views: 2075

11s is nice, what about 29 psi run, when you fix your stuff?