www.ka-t.org

the unit that turns on your a/c, how well of condition is that in? those can go faulty too.
if you dont know what im talking about, its the unit that you adjust your blower speed, cold and hot settings on.

that kinda sounds difficult to answer, i would like to see what other people would say. So when you try and turn on your a/c, does your condesoner turn on? fans kick on? But nothing blows out of the vents? Theres no cabin filters in 240sx so if someones tells you that there full ****. But then somet...

Yeah it really sounds like something touching or grounding out a little bit. I would check out your speakers wires and see how there connected. Aftermarket speakers? I remember once my rear speaker wire caps fell off and they rubbed together sometimes driving and sounded like ****

FYI before you go take it off, which isnt that bad, but a lot of **** to remove, you should wait till someone else has a go at this problem. you only posted it today LOL

WOWOWOWOWOW dont just rip **** apart of you dont know how to check wires. You need to take your time with things. ITS very easy to over look things. Now, if you have your stereo on and your parked, and you turn your wheel all the way to the left it becomes static? How is your deck hooked up? Do you ...

haha yeah my lights go dim everytime i engage a switch or when my sub kicks. could be my battery. honestly i would hook up ur fans by itself and run it to a switch, aint that hard to turn on when u turn ur car off. and run ur fuel pump the normal way lol factory wise.

oh ok so you got a kouki s14? Where you located? it helps LOL Also, how secure are all your deck wires? is everything secured and wrapped properly? You gotta make sure nothing is touching each other that shouldnt. hot and ground etc. Sounds like when you turn somethings moving and touching something...

LOL that sounds frustratinggg
Is this like an 89?
Details of your car please

lol 200 posts!

LMAO well rotor and cap did help, but turns out it was the dizzy i think. I swapped it out with another one with the new rotor and cap, got it timed perfect, and so far so good! SO HOPEFULLY if the car runs and maintains its self well for the next couple months, im going to do a 5 speed swap and and...

Rotor and cap!!!!!! Car is been running fine and dandy Has never died out once or nor has it had idling issues. THO is did die once after i replaced the cap and rotor with a new one. Before i replaced it with a oem used one that was prety clean, thus solving my issue, so i went and just bought a new...

yes fuel pumped read good on multimeter

my rotor is pretty rusty, and thers some white lines on the cap next to the pins, which means arching? i just ordered a new cap and rotor and should have it by 3 today, i still havnt installed my nismo thermostat. i really wanna!

*****
So should i just buy a new one?
What are the chances that both dizzys where bad LOL
I guess ill start looking for a new one

lolol 3 posts up i said i changed dizzy. lolol when i bought the car, the guy said it was the dizzy and he threw in a spare for me. Got it changed out at Goodyear and it didnt make a difference at all. I havnt looked at the rotor and cap yet, but i did look at the old one. Not really too sure how to...

What do you mean? How come you say that mang?
btw where is the ICM?

im gonna replace the rotor and cap, and see how much a ignition control module is, I heard that if icm overheats, it can cause ark jumps and etc. My car performs well at cold, warm and hot, but after a really good warm up, and driving, is when she acts up. He seems to might think its an acrhing prob...

well, my car doesnt run that bad, where i would think its a faulty spark or injector. I possibly think its a leaky injector, or im not getting enough fuel. All my car is doing is having a jumpy idle, and sometimes it shoots white smoke and smells. This dosesnt happen until the car is warmed up tho m...

SWEEEET found a page with answers to the Crank Angle Sensor Install. YOU DONT NEED IT FOR THE OBDII, car will run without it, BUT you will always have a CEL. http://forums.nicoclub.com/s13-ka24de-transmission-conversion-for-the-obdii-s14-write-up-t384931.html This is a great write up, and when i do ...

yeah def check your fuses. Also do you have any loose wires hanging around? Anything open to air or water? My 89 hatch gave me electrical issues like that sometimes. I would get in the car and turn my lights on and like something else would turn on. if i turned on my dome light, my cluster lights wo...

Cyl 1. 175psi
Cyl 2. 180psi
Cyl 3. 175psi
Cyl 4. 170psi

So I got some great numbers here. So my idling problem must be fuel related.
Maybe a new fuel pump? Walboro?

i have no emission laws, i live in Hawaii

haha even tho no one answered my question, it answered it self. The bell-housing is the actually tranny here in this case. Some other engines have separate bell-housings. I was thinking i was going to need something in between the block and tranny, thus the bellhousing. SO GREAT! This tranny will bo...

The bellhousing is seperate from the tranny right??
Or am i just an idiot... i havnt looked at my tranny yet, at my pops house.
the bellhosing holds the starter right??
Anyway, i just dont wanna drill a hole into anything LOLOLOL, i just want everything to bolt up.

The bellhousing is seperate from the tranny right??
Or am i just an idiot... i havnt looked at my tranny yet, at my pops house.
the bellhosing holds the starter right??
Anyway, i just dont wanna drill a hole into anything LOLOLOL, i just want everything to bolt up.

I have everything for the swap except clutch, pressure plate, and flywheel. I have a 1996 OBDII s14. The trans i have i believe is 93. Now, can you use the automatic bellhousing or is that stupid? I might as well drill a hole for the crank postion ceneter? I have researched and nobody has clearly sa...

did you end up not using the CAS?

I have a couple questions...
I have a 93 dohc 5 speed trans.
Will my automatic bellhousing work?
I have a 96' obdII ka24de, so is it important that i have my crank angle sensor installed?
Above it says that the obdI trans doesnt have it(the 5 speed tranny i got).
So what do i have to do?

Was you're car running rough?

my car runs like complete crapppppp. its like im running only 3 cylinders