www.ka-t.org

I asked this before but i didn´t got a straight answer. To get consult from this ecu (U12) into my laptop, i need to solder the 5 wires to the ecu pins, plug the connector on the blazt cable and the usb, from the blazt cable, to my laptop, and with the right usb drivers i should get consult on the l...

I just checked the Board # and it´s a G41!



So it´s a U12 ecu!? I´ll have to test the wires.

Hi, i decided to take all the turbo stuff off, to check how is the engine working in N/A "mode"! I haven´t drove it around to test it, but when i first started it, it was idling at 11.0/11.5 AFR, 60 PSI oil pressure, good numbers! When i removed the manifold, i noticed this, http://img253....

Hi, like the title says, i´m looking for pictures of stanza ecus with consult, i know this probably has been covered here, but i didn´t found anything, and hybridka is down. This is the consult cable i will be using, and i´m about to order a stanza ecu. http://img338.imageshack.us/img338/9606/connec...

Hi, i realized i have a 240SX ecu and not a stanza, i got to this conclusion because i know that a 240SX tune (bin) does not work properly on a stanza ecu and vice versa, so i used the tune i have on my stock ecu and placed it on the stanza ecu, and the engine was working well, this didn´t happened ...

I was just told that i will not get consult out of this ecu, because this is not a consult ecu, despite it has the tx and rx pins, it´s not supported by any tester! Here´s how i have it at the moment, http://img135.imageshack.us/img135/3171/ecuwires1.jpg http://img412.imageshack.us/img412/3166/conne...

Do you guys know if i need to install a consult board on the stanza ecu, or i should be able to connect it to my laptop and get consult just by soldering the wires directly to the ecu pins like in the pictures above? I´m using a blazt cable and Nissan DataScan software! I´m still trying to make it w...

pm´d!

No, not working yet. I´m going to uninstall and reinstall the usb drivers to see if it helps!

Yes, i have ecu TX connected to consult RX and ecu RX to consult TX, not working, i even tryed swapping them, but still no results.
I´ll take some pictures tomorrow of the ecus current state, maybe i´m forgeting something, and post them here!

Hi, i wired the ecu to the female plug, installed the cable drivers and NissanDataScan software, but i still can´t get consult, so i tested the voltage of the wires from the ecu and i have power, clk, tx and rx voltage, when i press "connect" on the software i get a voltage change on the e...

Yes, i´m using real clamps, at the time i took the pictures i was 1 clamp short so i used a zip just to hold it in place, it´s already fixed!

Thanks

Hi, here´s how i did mine...







But mine is a ebay oil return kit, so far no leaks!

Ok, so like i was running 460cc injectors and stock maf with good afr numbers i decided to upgrade to my z32 maf, and when i tryed a few tunes i got from hybridka, they where all idling very rich 10.0 afr and richer, so yesterday i decided to test the voltage to see if i had any wires connected the ...

Ok, i´ll look for it

Thanks

I was searching for 280ZX pumps and found this one, http://fcpimport.com/products/nissan-en ... 0-028-0081
Can you confirm if this is the one i should use or should only use the Sealed Power Pump?

Ok, so on saturday my spark plugs got toasted. i went to a couple of auto parts stores but they didn´t have them in stock, so i order it and pick them up today, after installed on the engine, it worked smooth again. Then i tested a tune i had here (460cc, stock maf), and i got these numbers, cold st...

Mark, i found the oil pump part# you provided, a few post back, #224-41901, can you confirm, http://www.summitracing.com/parts/SLP-224-41901/ and is it complicated to install?

No, i haven´t replaced the oil pump yet, let me know the part #. It´s kind of hard for me to do a rebuild right now, all the parts i need, i have to order them from the estates, and they became expensive with shipping and customs costs. To be honest i forgot all about the oil pump, so i´m going to s...

Can you tell how to do a leak down test? What will i need and how should i do it? Is it very hard to do? I have never done this test before!

My compression is about 150 psi all around from last time i checked, when i replaced the spark plugs.
The car smokes for about 30 seconds, a bit after i start it up, then the smoke goes away!

Hi, i´ve been away for a while and only now i got some time to work again on the car. I want to solve my oil pressure problem and was hopping you guys could give any ideias! With 10w40 synthetic oil i got a very low pressure after warm up, 10/5 psi, then i changed to 15w40 synthetic, and the pressur...

Here´s the U12 KA24E xdf file,

http://www.mediafire.com/?o4kw97xjpokw15n

for those like me, that want to get consult out of the 89 240SX!

But i also found soldered, pin 46 - ECU Backup Power and pin 48 - ECU Ground, anybody out there uses this pins? For what i´ve seen in many topics/forums they only use the 3 pins (7, 14, 15)!

I decided to order the blazt consult cable + the female connector, and started looking online for my ecu diagram to confirm if the wiring is correct and to know which wire goes were so i can do the wiring into the female connector, and found some curious info. According to the numbers on my ecu lid,...

Ok, so after searching around, i think my best option is to make a cable with a serial plug on one end and a nissan female consult connector on the other, here´s a pic of the connector, http://a.imageshack.us/img830/458/femaleconsultconnector.jpg With this plug installed i can get any of this cables...

I´ve emailed plmsdevelopments and ecutalk, asking if they make theyr consult cables with serial connector, instead of the nissan 14 pin connector!

I like the idea, here´s the ka24e xdf file,

http://www.mediafire.com/file/isi6c2cumum5eti/KA24E.xdf

If anybody want´s, i can upload my stock 240SX N/A tune, let me know!

Do you guys know where can i get a consult board with 2 serial connectors, so i can plug it to my existing cable, or with one serial and one usb connector?

I tryed that, still doesn´t work. I tryed with the ignition in the on position and also with the engine working, no response.
I was thinking, don´t i need to hook up a board between those 2 plugs that are connected together in the picture ( can´t remember theyr name)?