Search found 117 matches
- Wed Mar 27, 2013 10:33 am
- Forum: KA-T Chat
- Topic: anyone interested in a build template spreadsheet?
- Replies: 21
- Views: 3899
As an Engineer I'm all about spreadsheets. Bitches love spreadsheets. I think a good place to start would be to start a thread where people could copy and paste from the OP into their post and fill in the blanks. That way all of the information would be in one place and we could keep an updated spr...
- Wed Jan 30, 2013 10:40 am
- Forum: KA-T Chat
- Topic: Bolt broke off in alternator
- Replies: 1
- Views: 836
Get another 10 mm bolt the same length. Don't worry about the plastic piece, if it breaks it breaks if not fine, just break that 10mm thats holding the + wire loose so you can get that alternator down where you can work on it. As far as the broken piece, it sounds like its the piece that goes throug...
- Wed Jan 30, 2013 10:18 am
- Forum: KA-T Chat
- Topic: Rod knock - Well so i thought!
- Replies: 6
- Views: 1413
Hows about one of the s buckets a I had a while back that was a flip car I bought running but not driving. Needed the trans pulled and clutch fork put back on the TOB, do that, awesome :D Runs+drives great. Just about ready to sell 8) ....wait rod knock :evil: Although when i listened(This was a %10...
- Wed Jan 30, 2013 10:04 am
- Forum: KA-T Chat
- Topic: gauges/ignition switch wiring
- Replies: 4
- Views: 1398
Re: gauges/ignition switch wiring
If im going to run a water temp and oil pressure gauge, and probably a aem uego wideband, eventually a truboost. Can I use power from the ignition switch for all four of them or will that overload it. Im definitely no electrical engineer, so I really have no idea. And can I use the same ground wire...
- Wed Jan 30, 2013 9:54 am
- Forum: KA-T Chat
- Topic: Bolts, gaskets, and nuts.
- Replies: 20
- Views: 3019
awesome. okay, I just ordered the JGS kit. Ill see if I can dig up some locking washers and Ill just reuse my gaskets. Coolness Riiight....Out of the 15+ ka's I have had and motors I still have I think maybe 1 or 2 this didn't happen to. Unbelievable...This is a good thread though, when I rebuild m...
- Tue Dec 04, 2012 5:56 am
- Forum: KA-T Chat
- Topic: Best place for brake pads?
- Replies: 4
- Views: 623
Rockauto typically has hella cheap parts and i have bought several brake pads at great prices. They have everything from economy to street to performance. It'd be at least worth a look to see if the price/performance for a set would warrant the work/money but sometimes they have stuff on closeout/cl...
- Mon Nov 26, 2012 10:11 am
- Forum: KA-T Chat
- Topic: Got some 17x10 FN01R-C HVs this weekend
- Replies: 21
- Views: 4579
The car deff looks better a nice fresh color like that. I like that you removed the paint and they have that clean look but to the OP white over black, they still may look good white w/your current scheme. Overall at least you got HV's (Only way to go w/FN's IMO) and you should've totally painted th...
- Tue Nov 20, 2012 12:12 pm
- Forum: Welding/Fabrication
- Topic: Welder Options
- Replies: 18
- Views: 5691
I also have a harbor frieght one but it is the mig/flux.....So if needed you can hook up gas and not have to use flux. I think it was $180??? It has served all the uses I have needed so far which sounds about exactly what you are looking to do. Has been put through 2+ years of abuse and still going ...
- Tue Nov 20, 2012 11:58 am
- Forum: Welding/Fabrication
- Topic: Costum Body..
- Replies: 14
- Views: 5404
- Tue Nov 20, 2012 11:45 am
- Forum: KA-T Picture Threads
- Topic: drifter92's 1991 240sx KA24DE-T Build Thread - New Member
- Replies: 4
- Views: 2587
- Tue Nov 20, 2012 11:41 am
- Forum: Car Chat
- Topic: 240 vs teg....thoughts?
- Replies: 23
- Views: 4448
I'm not going to research it but throwing it out there, don't si/gsr trans' have a much shorter ratio than our gearbox? My brother has a dc2 w/an ls 5 spd and bi*ch is pretty quick i must say. B Series is to Import Scene as 350 is to Domestic Scene....Have potential and most modded/swapped motors. I...
- Wed Nov 14, 2012 7:32 am
- Forum: Car Chat
- Topic: Daily driver ride height
- Replies: 36
- Views: 12376
^ I threw up a little bit in my mouth. WHat do you expect to see from msnbc and/or Rachel Maddow? Of course she's going to pat him on the back, democrats on the back, etc etc.... Half of what she was trying to state as facts, are total b/s and propaganda....Just like what the elite controlled media ...
- Fri Nov 09, 2012 7:47 am
- Forum: KA-T Picture Threads
- Topic: Need help with diy fuel rail
- Replies: 6
- Views: 1625
Why not just buy a ^ Beercan rail? Same thing you are trying to do but done well. He doesnt make much out of it for profit anyways and is all american goods! Plus, if you do get one you can take his measurements/product and replicate it w/the materials you have to make one the right way for sure an...
- Thu Nov 08, 2012 8:17 pm
- Forum: Car Chat
- Topic: Daily driver ride height
- Replies: 36
- Views: 12376
Current daily on S14 rear KTS's,Front Tein HR's. S14 Godspeed rucas,toes,tensions. S14 FLCAS, Tein inners, CS outers, S14 front hubs/spindles. BC Q45 camber plates, Battle version Tensions. Alignment cost $150 :o Yeeeeaaa. http://i238.photobucket.com/albums/ff290/TiffxOxnay/Q45/Y33002.jpg http://i23...
- Thu Nov 08, 2012 8:13 pm
- Forum: Car Chat
- Topic: Daily driver ride height
- Replies: 36
- Views: 12376
Beater N/A s14, actual daily'd ride height on JIC FLTA-2's http://i238.photobucket.com/albums/ff290/TiffxOxnay/6%2018%202011%20Green%20S14/GreenCarsunset.jpg http://i238.photobucket.com/albums/ff290/TiffxOxnay/6%2018%202011%20Green%20S14/GreenS14002.jpg http://i238.photobucket.com/albums/ff290/Tiffx...
- Thu Nov 08, 2012 8:11 pm
- Forum: Car Chat
- Topic: Daily driver ride height
- Replies: 36
- Views: 12376
Nissans I still have and have actually daily'd the past couple years in order from earliest to latest: http://i238.photobucket.com/albums/ff290/TiffxOxnay/Daily%20Maroon%20S14/100_1440.jpg http://i238.photobucket.com/albums/ff290/TiffxOxnay/Daily%20Maroon%20S14/100_1441.jpg http://i238.photobucket.c...
- Thu Nov 08, 2012 7:48 pm
- Forum: KA-T Tech. Basic
- Topic: Inner/Outer tie rod install
- Replies: 17
- Views: 2791
haha finally someone. as for getting outters off w/o fubaring them all you have to do is hammer on the actual knuckel right next to it. you gotta swing like an ape with a big hammer but works eveery time. note that when u use tein inners you will not be able to use that safety tab thing anymore. US...
- Thu Nov 08, 2012 7:37 pm
- Forum: KA-T Chat
- Topic: can i put a single cam head on a dual cam block?
- Replies: 10
- Views: 1646
lawl. if the motor overheated, then pull the head off and inspect it. Change the valve seals and resurface the head and you will be good to go :idea: edit: single and dual are different, but check this out noob :D http://zilvia.net/f/engine-tech/328784-ka24e-de-question.html Goes w/out saying but e...
- Thu Nov 08, 2012 12:49 pm
- Forum: KA-T Tech. Basic
- Topic: Inner/Outer tie rod install
- Replies: 17
- Views: 2791
Okay, Since no one posted anything helpful on the actual labor: 1: Undo cotter pins and main nut(You'll most likely need an electric/air impact) 2: If you dont care about the current ends and plan on tossing them in the trash bang the top of them w/a hammer until they are out. Otherwise if you have ...
- Thu Nov 08, 2012 12:10 pm
- Forum: KA-T Picture Threads
- Topic: Need help with diy fuel rail
- Replies: 6
- Views: 1625
Why not just buy a ^ Beercan rail? Same thing you are trying to do but done well. He doesnt make much out of it for profit anyways and is all american goods! Plus, if you do get one you can take his measurements/product and replicate it w/the materials you have to make one the right way for sure and...
- Thu Nov 08, 2012 12:07 pm
- Forum: Road Racing/Autocross/Drifting
- Topic: SKID RACING @ Lime Rock Park!!! 11/17/12
- Replies: 7
- Views: 7652
- Thu Nov 08, 2012 11:55 am
- Forum: Road Racing/Autocross/Drifting
- Topic: Mods to increase s14 front camber
- Replies: 8
- Views: 9066
Its not very common, but there is an eccentric bushing/bolt setup for the flca, they're pretty expensive, around $250 iirc. It seems as though you are trying to work with what you have for now though(Which i understand) It is very common and many ppl have done so safely(Thus far at least) what you a...
- Thu Nov 08, 2012 11:44 am
- Forum: KA-T Chat
- Topic: can i put a single cam head on a dual cam block?
- Replies: 10
- Views: 1646
- Tue Nov 06, 2012 11:03 am
- Forum: KA-T Chat
- Topic: Chris Forsberg KA-T Drift Missile
- Replies: 7
- Views: 2151
Oh god, that exhaust is ugly. He could've been more creative with it yeeeeeah +1 for sure looks like **** and you would be eating exhaust fumes the whole time of driving... +1 both......Forsberg coming to a KA-T.org near you? LOLZ We have all seen(From what we can see w/those wonderful pics) much b...
- Thu Nov 01, 2012 10:14 am
- Forum: On the Street
- Topic: S13 vs Prelude < First kill :D
- Replies: 7
- Views: 2524
An H22 lude was my 1st car(Wanted a 240 but there were none in the immediate area at the time LOLZ)....Deff a quick car out the box when compared to several other 4+6 cyl comparable imports/sport compacts. Hell, I walked a harley w/2 of my friends in car from a dig when i was 16...however yeah they ...
- Thu Nov 01, 2012 9:24 am
- Forum: KA-T Chat
- Topic: Exhaust: whats everyone running?
- Replies: 18
- Views: 3923
- Thu Nov 01, 2012 9:13 am
- Forum: KA-T Picture Threads
- Topic: My daily driver.
- Replies: 7
- Views: 2485
- Wed Oct 31, 2012 10:53 am
- Forum: Road Racing/Autocross/Drifting
- Topic: Open diff drifting
- Replies: 8
- Views: 8918
- Wed Oct 31, 2012 10:37 am
- Forum: KA-T Chat
- Topic: Free set of stage 2 cams for ka24de
- Replies: 85
- Views: 31851