Page 1 of 1

319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Tue Nov 06, 2012 12:28 pm
by ka-t240sx
-CP pistons 8.5:1 iirc
-Eagle rods
-BC valvetrain minus valves
-Stock intake manifold. (kinda wanna try the xcessive one, opinions?)
-BC 272 cams
-Holset hx35 w/12cm^2 exhaust housing
-Turbosmart 38mm external wastegate w/8 psi spring
-3"straight pipe to dual 4" tips
-clutchmasters fx400 clutch
-MegaSquirt v3
-760cc side feed injectors
-LS coil packs w/MSD 8.5mm wires
-arp 11mm head studs
-94 octane pump gas
-bkr7e, gap @ .028



*sidenote: theres alot more im probably forgetting and im doin this on my lunch break, so i don't have alota time at the moment, sorry. but If ya'all need anymore information just lemme know.

I've had a few stock ka-t's i can try to remember the specs on them too if wanted.
might have a dyno graph or two on those ka's.



graph.
Image

motor
Image
Image
Image
Image
Image

Posted: Tue Nov 06, 2012 12:31 pm
by supakat
Fuel?

Posted: Tue Nov 06, 2012 12:32 pm
by ka-t240sx
oops, my bad. 94 octane pump

Posted: Tue Nov 06, 2012 12:37 pm
by beercandrifter
some awesome numbers for 10psi

man i wish i would have dynod my car at 25psi on that setup, would have probably just slapped in new pistons lol.

looking good man

Posted: Wed Nov 07, 2012 6:33 am
by jholman05
Nice very impressive for such low boost!

Posted: Wed Nov 07, 2012 6:51 am
by supakat
Did you degree the cams?

Posted: Wed Nov 07, 2012 7:55 am
by ka-t240sx
supakat wrote:Did you degree the cams?
No, not really, just shimmed them properly, I still have the stock cam gears.
Should probably invest in some JWT gears haha.

I haven't had the time/money to get back on the dyno yet.

I wouldn't mind going for 16-18 psi on pump for next year but im more than happy with where im at right now.

Posted: Wed Nov 07, 2012 7:59 am
by sdaigle240
wow thats the stock housing? that spools sooner than i thought it would. very nice.

Posted: Wed Apr 24, 2013 1:03 am
by Mercury_Hg
Are you running a BOV? I anticipate having a setup very similar to this one in the near future.

Arias 8.8:1 Pistons
Eagle Rods
Rebuilt head
JWT S1 Cams
HX35
JGS400 wastegate 7-8psi
3" dp w/ 2.5 dual exhaust
White bunny clutch setup
Nistune Type 3 board
740cc injectors

Posted: Wed Apr 24, 2013 12:47 pm
by airman
Cool. I somehow missed this dyno sheet. Very similar to my old setup. CP, Eagle, HX35, 10-15psi, yadda yadda. At 10psi this is about what I was seeing in virtual dyno, so cool. Your cams help out though, stock S13s for me.

And oh, seeing your dyno curve reminds me that I miss my HX / turbo in general :( 300ft-lb at 4k RPM? Yes please!

Posted: Wed Apr 24, 2013 5:33 pm
by KA-T S12
What manifold is that?

Posted: Thu Apr 25, 2013 6:14 pm
by ka-t240sx
Mercury_Hg wrote:Are you running a BOV? I anticipate having a setup very similar to this one in the near future.

Arias 8.8:1 Pistons
Eagle Rods
Rebuilt head
JWT S1 Cams
HX35
JGS400 wastegate 7-8psi
3" dp w/ 2.5 dual exhaust
White bunny clutch setup
Nistune Type 3 board
740cc injectors
Yes Tial Q 50mm

Posted: Thu Apr 25, 2013 6:22 pm
by ka-t240sx
airman wrote:Cool. I somehow missed this dyno sheet. Very similar to my old setup. CP, Eagle, HX35, 10-15psi, yadda yadda. At 10psi this is about what I was seeing in virtual dyno, so cool. Your cams help out though, stock S13s for me.

And oh, seeing your dyno curve reminds me that I miss my HX / turbo in general :( 300ft-lb at 4k RPM? Yes please!
I noticed a huge difference in switching from stock cams to the 272's. Some day soon i plan on degreeing them properly. I have a feeling there is some more power to be made with them degree'd properly.

I love my holset. Wouldn't trade it for anything else and 300 ft-lb @ 4k is pretty awesome. Just wish it didn't drop so much from 6k to redline.

Posted: Wed May 15, 2013 4:39 am
by sr20drag
bullseyepower T3 .70ar turbine housing will give you 300rpm's of spool and lose nothing up top. Well worth the $200 they go for on extremepsi. I made 411whp with one at 20psi on a sr20 on 93oct and a jwt rom tune years ago. It will like 16-18psi a LOT better. Jst starting to get into the effeciency range of that turbo at 18psi. They really love E85 and 40psi.....
:D

Posted: Wed May 15, 2013 5:58 am
by supakat
I bet those head studs are helping out a lot. I was making around 320whp on 10psi but lifted the head. Great power and I love the HX. Great turbo.

Posted: Wed May 15, 2013 6:23 am
by jaysol92
nice numbers for 10 psi ! arp head studs ftw

Posted: Wed May 15, 2013 6:27 am
by supakat
jaysol92 wrote:nice numbers for 10 psi ! arp head studs ftw
He has 11mm not the 10mm. I have 10mm but still managed to lift the head. I think it first started when I was at 15psi tuning and ran a 600cc bike. LOL.

Posted: Thu May 16, 2013 7:01 am
by jaysol92
supakat wrote:
jaysol92 wrote:nice numbers for 10 psi ! arp head studs ftw
He has 11mm not the 10mm. I have 10mm but still managed to lift the head. I think it first started when I was at 15psi tuning and ran a 600cc bike. LOL.
damn! running with bikes and lifting heads with arps, how much you putting down??

Posted: Thu May 16, 2013 7:47 am
by Berserker
http://www.ka-t.org/karey_d.php

He ran 700 whp with 10mm arp head studs. I think miami240 said its all in the tune.

Posted: Fri May 17, 2013 9:22 am
by supakat
Yea, it is all in the tune. I leaned out to 13.5 afr's I think and my timing was advanced quite a bit. I however got a new timing map. Runs great even for 13psi. ARP's and cosworth has been holding up. 400whp will run with 600cc bikes. you need like 700whp to run with 1000cc.

Posted: Fri May 17, 2013 12:48 pm
by Berserker
Yeah I had same issue when I leaned out. I threw in new felpro headgasket with 10mm arp headbolts resurfaced head and ran that motor 21 psi 400whp on 50 trim(e85 stock block) for a while before I build this current motor. Sold that motor with excelent compression.

Posted: Fri May 17, 2013 7:00 pm
by ka-t240sx
sr20drag wrote:bullseyepower T3 .70ar turbine housing will give you 300rpm's of spool and lose nothing up top. Well worth the $200 they go for on extremepsi. I made 411whp with one at 20psi on a sr20 on 93oct and a jwt rom tune years ago. It will like 16-18psi a LOT better. Jst starting to get into the effeciency range of that turbo at 18psi. They really love E85 and 40psi.....
:D
I would LOVE to run E85 but there is absolutely no stations up here that sell it.
94 octane is the best i can get :(
I'm hoping to toss her back on the dyno in a couple months and run 17-20 psi. There's still a few small issues i need to sort out before i bump up the boost.

I'm thinking about switching to the full race twin scroll manifold. I'm tired of constantly cracking this current manifold. And possibly the excessive intake but i don't really want to loose my mid-range for a little top end gain.

Posted: Fri May 17, 2013 10:08 pm
by jaysol92
Berserker wrote:Yeah I had same issue when I leaned out. I threw in new felpro headgasket with 10mm arp headbolts resurfaced head and ran that motor 21 psi 400whp on 50 trim(e85 stock block) for a while before I build this current motor. Sold that motor with excelent compression.
400 on stock internals is nice , I'm shooting for that range on 93 pump with meth on a 50 trim also.

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Wed Jul 10, 2013 10:32 pm
by ka-t240sx
Heres a vid, Rear tyres were 245/45/17 Falken Azenis rt-615k with ~25psi. She feels kinda slow :/ maybe im just used to 10psi lol. Don't plan on upping the boost until i get a better exhaust manifold/twin scroll.

http://youtu.be/7KujBhrQECs

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Thu Jul 11, 2013 10:55 am
by neverlift
0 mph ftw lol

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Thu Jul 11, 2013 8:08 pm
by toky042
damn pulls hard

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Thu Jul 11, 2013 8:29 pm
by ka-t240sx
neverlift wrote:0 mph ftw lol
LOl yeah, speed sensor is friggard.
toky042 wrote:damn pulls hard
Yeah, not bad for only ~10 psi. Startin to feel slow though. Probably just getting used to it that's all.

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Fri Jul 12, 2013 11:42 pm
by toky042
hoping to get the same turbo, seems pretty good eh

Re: 319.2 rwhp / ~330 tq @ 10psi, built KA w/hx35

Posted: Mon Jul 15, 2013 5:39 am
by Grant
good number man, gotta love the holset turbo and bc cams.