hpipro4 S13 KA24DE-T Build
hpipro4 S13 KA24DE-T Build
been lurking around the forum but never really posted nor created a thread until now. im mostly on zilvia but i figured id post my build thread here too!
my 1st car.... my 1st build. all works done by me with my own bare hands and lotza sweat & hardwork! started back in 2008 and my build has been ongoing.....
car is a 92 s13 salvaged title lol bought off a chick that drifted it. cost me 2600 which i now realized i overpaid for it! needed new tires and a/c compressor was hanging. brown interiors with welded diff lol
1st day i got the car.....
didnt know a thing about s13 till i actually went out in the garage and got dirty lol
got bored one day and decided i was going to make the bay look tucked! so there i went....
started with engine harness...
after engine harness was done i decided to re-locate battery, and fuse/relay boxes to the inside....
also installed few electronics.......
August 2009 the car was up and running....
September 2010 went all out.....
stance LX+ luv em!
suspension techniques sways
my clutch went out so i went with all this
jdm visor
rps13 kouki center overlay
January 2011 decided to go ka-t
scored a ka-t stuff locally and decided to take out dash again and re-wire/relocate where my gauges will go...decided that im going to ditch center vent and creat my own triple gauge pod using fiberglass stay tuned...
moved some of the relays to the top so their not showing underneath glovebox.
i g0t very creative and modded my toplite that i never use and manage to fit my greddy mss(use as fan controller) in there w/o doing anything to much just using dremel w/cut off wheels and viola!!!!!i think it turn out perdy cool. wat ya think?
May of 2011 my finished KA-T
t25, n60 blow thru, 370cc, rs-enthalpy rom tune, isis fmic, pbm cobra dp, 255lph walbro, areomotive fpr....
so i decided to retrofit another h4 housing with morimoto d2s bi-xenon projectors.
Jan 2012......
decided to cover the entire interior with sound deadening material i got from ebay called fatmat. same stuff as the dynamat but less expensive. while im at it, going to laydown a new blk carpet frm stockinteriors.com cheaper if you bid on their ebay store. while gutting the interiors, some of my wirings were on the way so im re-wirings things around....enjoi
tear down....
ya! ill be running optima d51r yellow top aka honda battery lol
fatmat 50mil
this my old fuse panels....no problems but i needed more stuff to fused..
mock up of the new fuse panels.....got a bigger fuse block n midi holder(replaces the 75amp fusible links)
the current and finished relays
re-did brown interior into blk carpet
greddy ti-c 80mm catback
resonator sat really low and hits my swaybar.....
decided to buy myself an everlast pt185 micro tig welder...never tig bfore so bare with me!
was tired of the resonator scraping everywhere so i decided to make just 3" 304 ss straight pipe. my 1st time tig welding stainless so it look like crap but will work for now. i did back purged.
also tig my own coolant overflow tank and powdercoated wrinkle blk
also bought an eastwood powdercoater & harbor freight blast cabinet....luv em both!
some examples what it can do.......
man i hate having to smog the damn car every 2yrs! forgot to swap out aeromotive fpr & 255lph....**** was running rich!
carb legal KA lol
only drove 235miles in 2yrs!!!!!then out came the engine.
my 1st car.... my 1st build. all works done by me with my own bare hands and lotza sweat & hardwork! started back in 2008 and my build has been ongoing.....
car is a 92 s13 salvaged title lol bought off a chick that drifted it. cost me 2600 which i now realized i overpaid for it! needed new tires and a/c compressor was hanging. brown interiors with welded diff lol
1st day i got the car.....
didnt know a thing about s13 till i actually went out in the garage and got dirty lol
got bored one day and decided i was going to make the bay look tucked! so there i went....
started with engine harness...
after engine harness was done i decided to re-locate battery, and fuse/relay boxes to the inside....
also installed few electronics.......
August 2009 the car was up and running....
September 2010 went all out.....
stance LX+ luv em!
suspension techniques sways
my clutch went out so i went with all this
jdm visor
rps13 kouki center overlay
January 2011 decided to go ka-t
scored a ka-t stuff locally and decided to take out dash again and re-wire/relocate where my gauges will go...decided that im going to ditch center vent and creat my own triple gauge pod using fiberglass stay tuned...
moved some of the relays to the top so their not showing underneath glovebox.
i g0t very creative and modded my toplite that i never use and manage to fit my greddy mss(use as fan controller) in there w/o doing anything to much just using dremel w/cut off wheels and viola!!!!!i think it turn out perdy cool. wat ya think?
May of 2011 my finished KA-T
t25, n60 blow thru, 370cc, rs-enthalpy rom tune, isis fmic, pbm cobra dp, 255lph walbro, areomotive fpr....
so i decided to retrofit another h4 housing with morimoto d2s bi-xenon projectors.
Jan 2012......
decided to cover the entire interior with sound deadening material i got from ebay called fatmat. same stuff as the dynamat but less expensive. while im at it, going to laydown a new blk carpet frm stockinteriors.com cheaper if you bid on their ebay store. while gutting the interiors, some of my wirings were on the way so im re-wirings things around....enjoi
tear down....
ya! ill be running optima d51r yellow top aka honda battery lol
fatmat 50mil
this my old fuse panels....no problems but i needed more stuff to fused..
mock up of the new fuse panels.....got a bigger fuse block n midi holder(replaces the 75amp fusible links)
the current and finished relays
re-did brown interior into blk carpet
greddy ti-c 80mm catback
resonator sat really low and hits my swaybar.....
decided to buy myself an everlast pt185 micro tig welder...never tig bfore so bare with me!
was tired of the resonator scraping everywhere so i decided to make just 3" 304 ss straight pipe. my 1st time tig welding stainless so it look like crap but will work for now. i did back purged.
also tig my own coolant overflow tank and powdercoated wrinkle blk
also bought an eastwood powdercoater & harbor freight blast cabinet....luv em both!
some examples what it can do.......
man i hate having to smog the damn car every 2yrs! forgot to swap out aeromotive fpr & 255lph....**** was running rich!
carb legal KA lol
only drove 235miles in 2yrs!!!!!then out came the engine.
Last edited by hpipro4 on Sun Feb 15, 2015 12:35 am, edited 14 times in total.
- street_240sx
- Belongs To The TOP CONTRIBUTING MEMBERS!
- Posts: 1923
- Joined: Sun Feb 10, 2008 7:31 pm
- Location: 520 AZ
- shift_down
- SuperMod
- Posts: 1833
- Joined: Mon Nov 28, 2011 11:00 am
- Location: tulsa oklahoma
Where did you mount your ps reservoir and coil?
Come at me bro
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539
Take a closer look.shift_down wrote:Where did you mount your ps reservoir and coil?
http://img268.imageshack.us/my.php?image=dsc06480k.jpg
12.96 @ 116.36 - 2.1 60ft - 11/2011
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel
- shift_down
- SuperMod
- Posts: 1833
- Joined: Mon Nov 28, 2011 11:00 am
- Location: tulsa oklahoma
Okay I see. Im going to try to fab that up as well.
Come at me bro
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539
That my good sir is amazing wire work. So clean
Are those MB Weapons I see?
Are those MB Weapons I see?
230k stock block
50 trim 16psi
810cc DW's
Z32 MAF
Enthalpy Tuned
*Sold*
Evo X Cornfed
http://www.youtube.com/LGmmkay
^ Youtube Channel ^
viewtopic.php?p=496648#496648
^ Build Thread ^
viewtopic.php?t=45057&postdays=0&postorder=asc&start=0
^ Considering E-Mance? Read this ^
50 trim 16psi
810cc DW's
Z32 MAF
Enthalpy Tuned
*Sold*
Evo X Cornfed
http://www.youtube.com/LGmmkay
^ Youtube Channel ^
viewtopic.php?p=496648#496648
^ Build Thread ^
viewtopic.php?t=45057&postdays=0&postorder=asc&start=0
^ Considering E-Mance? Read this ^
- 500hpKA240sx
- Encyclopedia-Nissan
- Posts: 1100
- Joined: Thu Jun 16, 2011 12:37 pm
- Location: Bourbon, MO
for sure in my top 5 favorite builds without a doubt.
viewtopic.php?t=53160&postdays=0&postorder=asc&start=0
Paul Walker- 1973-2013 Race In Paradise. you will be forever missed
Paul Walker- 1973-2013 Race In Paradise. you will be forever missed
- aaronlee97
- Encyclopedia-Nissan
- Posts: 1018
- Joined: Wed Nov 30, 2005 1:55 pm
- Location: Houston, TX
- emo_tactical9
- Belongs To The TOP CONTRIBUTING MEMBERS!
- Posts: 3086
- Joined: Tue Sep 18, 2007 3:21 am
- Location: Bowling Green, KY
I didn't know those visors at Autozone were JDM.
Just call me Adam.
95 240: DIYPNP and T28.
08 Honda Fit
84 200sx: Sold after almost 10 years.
My file hosting:Calum,MegaSquirt,FSM
95 240: DIYPNP and T28.
08 Honda Fit
84 200sx: Sold after almost 10 years.
My file hosting:Calum,MegaSquirt,FSM
hpipro4 wrote:thanks!!!mmmS13 wrote:That my good sir is amazing wire work. So clean
Are those MB Weapons I see?
yes sir they sure are mb weapons 17x9 +18 all around
I have the same wheels hah they look much better on your car. My cars black and I dont think they look as good on mine
Edit* Do you have a sound clip of without the resonator? I've got the same exhaust and curious of how it sounds, Im tired of it scraping the ground.
Last edited by mmmS13 on Thu Feb 07, 2013 3:39 pm, edited 1 time in total.
230k stock block
50 trim 16psi
810cc DW's
Z32 MAF
Enthalpy Tuned
*Sold*
Evo X Cornfed
http://www.youtube.com/LGmmkay
^ Youtube Channel ^
viewtopic.php?p=496648#496648
^ Build Thread ^
viewtopic.php?t=45057&postdays=0&postorder=asc&start=0
^ Considering E-Mance? Read this ^
50 trim 16psi
810cc DW's
Z32 MAF
Enthalpy Tuned
*Sold*
Evo X Cornfed
http://www.youtube.com/LGmmkay
^ Youtube Channel ^
viewtopic.php?p=496648#496648
^ Build Thread ^
viewtopic.php?t=45057&postdays=0&postorder=asc&start=0
^ Considering E-Mance? Read this ^
-
- Driving Mom's Station Wagon
- Posts: 41
- Joined: Wed Oct 03, 2012 8:47 am
- Location: Chipley,Fl
- 240sx-venezuela
- 240sx Wannabe
- Posts: 182
- Joined: Wed Sep 07, 2011 11:52 am
- Location: Maracaibo, Venezuela
A crazy build! That car received a new lease on life, good job!
Crower Rods
Arias Pistons (8.8:1)
Precision SC61 Turbo (Currently 17lbs)
POS AEM ECU
DMH Electric Exhaust Cut out
MSD 6+/Magnecor Wires
AFC Neo
AEM WideBand
AEM Serial Gauge
A.C.T 6 Puck Clutch
Custom Short Shifter
Stillen Strut Bar
ST Rear Sway Bar
Whiteline Front Sway Bar
Racing Line Endlinks
Brembo Drilled/Slotted Rotors
GC Springs/Tokico Struts
18" Centerline RPM's (15lbs!)
Arias Pistons (8.8:1)
Precision SC61 Turbo (Currently 17lbs)
POS AEM ECU
DMH Electric Exhaust Cut out
MSD 6+/Magnecor Wires
AFC Neo
AEM WideBand
AEM Serial Gauge
A.C.T 6 Puck Clutch
Custom Short Shifter
Stillen Strut Bar
ST Rear Sway Bar
Whiteline Front Sway Bar
Racing Line Endlinks
Brembo Drilled/Slotted Rotors
GC Springs/Tokico Struts
18" Centerline RPM's (15lbs!)
-
- Knows Some Stuff About 240's!
- Posts: 445
- Joined: Fri Nov 11, 2011 1:26 am
- Location: long beach
this is a freaking awsome build exactly what i wish i had time and money for, not bad tif for first time either, how much did it cost you to do all the fuse box wiring and stuff?
in a datsun 510:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
sdaigle240 wrote:beat that thing like it owes you money.
i do but not with the turbo...only NA and its loud even with the cat lol.mmmS13 wrote:hpipro4 wrote:thanks!!!mmmS13 wrote:That my good sir is amazing wire work. So clean
Are those MB Weapons I see?
yes sir they sure are mb weapons 17x9 +18 all around
I have the same wheels hah they look much better on your car. My cars black and I dont think they look as good on mine
Edit* Do you have a sound clip of without the resonator? I've got the same exhaust and curious of how it sounds, Im tired of it scraping the ground.
bride doesnt sell em pre-made. they do however sell the fabric and you change it out. yes all the relays are inside behind the glove box. unlike most people they hide their fuse/relay boxes on the fender wells. i re-did the chassis wires too.240sx-venezuela wrote:Does Bride sells those door panels? I also would like to know if you move all the relays from the engine bay to inside of the car
thanks!!ViperGT wrote:this is a freaking awsome build exactly what i wish i had time and money for, not bad tif for first time either, how much did it cost you to do all the fuse box wiring and stuff?
not very much its just very time consuming, i re-used oe connectors/wires just lotza de-pinning, soldering, heat shrink.....labelling,
- 240sx-venezuela
- 240sx Wannabe
- Posts: 182
- Joined: Wed Sep 07, 2011 11:52 am
- Location: Maracaibo, Venezuela
How hard was all that thing, how many hours? I did a re-wire to my ecu wiring because it was an auto trans car, Ive installed a manual and bought a megasquirtpnp, so I deleted all the unnecesary wires, looks very neat but is not enought with those relay and fuses boxes around the engine bayhpipro4 wrote:thanks!!ViperGT wrote:this is a freaking awsome build exactly what i wish i had time and money for, not bad tif for first time either, how much did it cost you to do all the fuse box wiring and stuff?
not very much its just very time consuming, i re-used oe connectors/wires just lotza de-pinning, soldering, heat shrink.....labelling,
Fantastic wiring job man. I've been wanting to do this to my car for a long time now.
Wiseco/Eagle, JWT S1 cams, BC valve springs, PT5857, ID1700 injectors, SR20DET ECU w/ Nismotronic, COP conversion with LS ignition coils, etc, etc...
--> YouTube channel --> my build thread
--> YouTube channel --> my build thread
spent countless hrs on it cant even remember how many lol....just getting all the wires out was alot work. i disconneted that big ol connector on the driverside and cut label wires there. then pulled out all the wires frm outide. had to extend some wires for it to reach to the pssenger side. ya took out alot of unecesary wires too.240sx-venezuela wrote:How hard was all that thing, how many hours? I did a re-wire to my ecu wiring because it was an auto trans car, Ive installed a manual and bought a megasquirtpnp, so I deleted all the unnecesary wires, looks very neat but is not enought with those relay and fuses boxes around the engine bayhpipro4 wrote:thanks!!ViperGT wrote:this is a freaking awsome build exactly what i wish i had time and money for, not bad tif for first time either, how much did it cost you to do all the fuse box wiring and stuff?
not very much its just very time consuming, i re-used oe connectors/wires just lotza de-pinning, soldering, heat shrink.....labelling,
so heres some update on my build.....
scored an awesome deal on a brand spankin new s15 t28
i know i dont need forged internals but like what they say go big or go home!
eagle rods got a good deal so why not!
reason why i pulled off the engine was to redo my oil pan bung but instead im going to rebuild the motor and bought some xcessive goodies! still need to get the lower pan tho
OSK timing chain kit
going to give this godspeed intake manifold a try....still need to do mods on it and clean it up better!
scored an awesome deal on a brand spankin new s15 t28
i know i dont need forged internals but like what they say go big or go home!
eagle rods got a good deal so why not!
reason why i pulled off the engine was to redo my oil pan bung but instead im going to rebuild the motor and bought some xcessive goodies! still need to get the lower pan tho
OSK timing chain kit
going to give this godspeed intake manifold a try....still need to do mods on it and clean it up better!
- shift_down
- SuperMod
- Posts: 1833
- Joined: Mon Nov 28, 2011 11:00 am
- Location: tulsa oklahoma
Hey post everything you had to do to mount that intake mani, I'm thinking about getting one also.
Come at me bro
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539
Fast
Reliable
Cheap;
You can only pick two, so choose wisely!
My build thread: viewtopic.php?t=57539