2nd time around

This is for all those PICTURE THREADS ONLY. Motor installs, product writeups, showing off your car, put the thread in here.
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Did you wire the Dakota digital to your tach or your speed sensor?
adamky
SuperMod
Posts: 3511
Joined: Wed May 31, 2006 6:40 am
Location: Louisville, KY

Re: 2nd time around

Post by adamky »

Speed sensor
Wiseco/Eagle, JWT S1 cams, BC valve springs, PT5857, ID1700 injectors, SR20DET ECU w/ Nismotronic, COP conversion with LS ignition coils, etc, etc...
--> YouTube channel --> my build thread
Image
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Ok. About to put my mojo on it
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Well. Since the new turbo I've been hitting 25psi on a 44mm tial with 2 springs that make right at 20psi. About to take the smaller spring out and run a boost controller. Hooked up air to the wg. It's opening properly
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Well the car is running decent. Put some new 275's in the rear and It doesn't break loose anymore. The only problem I'm having is starter issues with this z32 trans kit. I'm using the z32 side mount car quest starters. I've tried 4 of them. The car starts fine but after driving around I guess the starter gets hot and they drag the next time you try and crank it. Let the car sit for a while and it fires up like a new starter. I've added a ground to the starter and it didn't help. I'll be pulling the adapter plate and have it machined to use the stock ka starter
fishmando2
NooB
Posts: 1
Joined: Fri Jul 28, 2017 10:04 am

Re: 2nd time around

Post by fishmando2 »

Do you have the contact info for Kedbmx? I would love to switch to these Honda coil-packs using his harness.
tuzzio
240sx Wannabe
Posts: 102
Joined: Thu Oct 29, 2015 7:02 pm

Re: 2nd time around

Post by tuzzio »

I've had the same issue with my WG, where you just have to run a lighter spring. Seemed to me like 2/3 of desired boost = spring pressure.

example, my target boost was 18, so I put the 11 or 12 pound spring in. I do run a MBC though.

Also, I think jegs/summit makes relatively universal starter heat blankets.
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Inspired engineering is the name of his LED light company. Located in Florida. He does custom lights for jeeps and other jeep mods. Number is 1-305 814 5331
Iwannadrivemycar
NooB
Posts: 5
Joined: Mon Dec 25, 2017 9:45 pm

Re: 2nd time around

Post by Iwannadrivemycar »

I assume you are using an AEM wiring harness?
If so could i get a pic of how you wired it to the 4 pin plug on the distributor?

Thank you.
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

3 pin for honda k coils. They are oem denso. 12v, ground and trigger.
Iwannadrivemycar
NooB
Posts: 5
Joined: Mon Dec 25, 2017 9:45 pm

Re: 2nd time around

Post by Iwannadrivemycar »

I was asking about the wiring from the aem ems4 to the stock distributor.
Attachments
1226172240.jpg
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

Factory harness plugs into the aem v2 behind the passenger kick panel and is a direct replacement for the factory ecu. It's plug and play for my year car.
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

No special harness needed. Just have to wire in any extra sensors you want to add to monitor whatever you want.
User avatar
supakat
SuperMod
Posts: 8018
Joined: Sun Oct 08, 2006 12:13 pm
Location: FL

Re: 2nd time around

Post by supakat »

Hey Cham, glad to see you around. Keep up the good work.
12.96 @ 116.36 - 2.1 60ft - 11/2011
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Image
Build thread/Blog
YouTube Channel
cham
Dont Question My Nissan Knowledge
Posts: 597
Joined: Sat Mar 23, 2013 9:57 am
Location: lumberton, NC

Re: 2nd time around

Post by cham »

20180405_221629.jpg
Post Reply