I am using the MS II V3 board. Car is a 97 KA24DE. Using 4 coils for a wasted spark setup. I'm using this picture for reference and I'm not sure where (C) on the coil plug should go....
(A) on all 4 coils grounded to the manifold.
(B) from coils 1&4 will go to pin 36 on the DB37 connector.
(B) from coils 2&3 will go to pin 6 on the DB37 connector.
(C) ??????
(D) +12V from the fuel pump relay or other switched +12V source.
Thanks!
Am I wiring my LS2 coils up properly
- drewssc400
- Dreams of owning a 240!
- Posts: 92
- Joined: Tue Jun 07, 2011 11:41 am
- Location: Agana, Guam
- drewssc400
- Dreams of owning a 240!
- Posts: 92
- Joined: Tue Jun 07, 2011 11:41 am
- Location: Agana, Guam
-
- Knows Some Stuff About 240's!
- Posts: 445
- Joined: Fri Nov 11, 2011 1:26 am
- Location: long beach
Re: Am I wiring my LS2 coils up properly
lol that was it did you put in capacitors for noise reduction? or just wire it up? sorry to bring up old posts but im running through all these similar posts about ign coils making sure everyones ready to boost
in a datsun 510:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
sdaigle240 wrote:beat that thing like it owes you money.
Re: Am I wiring my LS2 coils up properly
I just wired mine up. I have thought about this but never had an issue with noise.
12.96 @ 116.36 - 2.1 60ft - 11/2011
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel
-
- Knows Some Stuff About 240's!
- Posts: 445
- Joined: Fri Nov 11, 2011 1:26 am
- Location: long beach
Re: Am I wiring my LS2 coils up properly
sounds good
in a datsun 510:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
arias 8.8 .020
eagle rods
clevite bearings
ferrea/exhaust supertech/intake stk
supertech springs and retainers
bc valve guides v2 cams currently crower 288/288 (no good)
port and polish
arp head, main, rod bolts
osk timing
current: custom log mani, TIAL mvr,
later: ati SD garret gtx3071 currently in my possession looking for gtx3576
custom downpipe
lol:
sdaigle240 wrote:beat that thing like it owes you money.
- Matt Cramer
- KA-T.org Sponsor
- Posts: 934
- Joined: Mon Sep 15, 2008 5:34 am
- Contact:
Re: Am I wiring my LS2 coils up properly
It's usually not a big deal. A bigger deal is that I recommend grounding the LS1 coils to the cylinder head, separately from the ECU.supakat wrote:I just wired mine up. I have thought about this but never had an issue with noise.
Matt at DIYAutoTune.com - Megasquirt ECUs, fuel injectors, wideband O2 sensor systems, and more
Nissan plug and play engine management now in stock!
Nissan plug and play engine management now in stock!
Re: Am I wiring my LS2 coils up properly
Correct Matt. I have the stock harness for the coils and one is grounded to head and other to MS. I have my coils hooked up to a relay for 12v as well.
12.96 @ 116.36 - 2.1 60ft - 11/2011
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel
13.1 @ 114 - 2.3 60ft - 8/2012
KA24DE-T
Build thread/Blog
YouTube Channel