dyno the 4-bannger :(

Dyno Sheets/Results Only! We have a separate forum about ECU Tuning and Theory
Post Reply
nx95240
KA-T.org Featured Ride
KA-T.org Featured Ride
Posts: 615
Joined: Tue Feb 24, 2004 5:59 pm
Location: Nooga,TN
Contact:

dyno the 4-bannger :(

Post by nx95240 »

well first off the car ran very good not like last time . not the #'s i was looking for but life a b**ch sometimes. i have a vid RYAN send to you sunday :wink: .

first run was @ 22psi and made 444rwhp then the 2nd run was around 30 psi it was 484 rwhp .torque was 464.@ 6400. the guy didnot go to 7k because it got lean and i told him to get off of it.i make most of my power at 6800 on all of the other dyno's. i got the problem fix and go back soon to shoot for the 500 mark .the car has what it take to get there iam learning everyday about it and i will get there soon.. not to far but so far away.
Mischievious
Dreams of owning a 240!
Posts: 99
Joined: Thu Aug 26, 2004 9:34 pm
Location: houston
Contact:

Post by Mischievious »

congrats man. you got a great running car man. awesome.
efeezi
Dont Question My Nissan Knowledge
Posts: 697
Joined: Mon Dec 06, 2004 5:01 pm
Location: Oklahoma City, OK

Post by efeezi »

Not too bad man. So what was going on that you only picked up 40hp from 8 psi?
300zx single turbo
715rwhp GT42
Structure240sx
KA-T.org Featured Ride
KA-T.org Featured Ride
Posts: 695
Joined: Thu Aug 12, 2004 11:50 am
Location: Sicklerville, NJ
Contact:

Post by Structure240sx »

a few hundred rpms short is what it was

almost there buddy, im getting back to the dyno this week prolly
elks240
Dont Question My Nissan Knowledge
Posts: 699
Joined: Sun May 02, 2004 8:08 am
Location: Midwest City , Oklahoma

Post by elks240 »

awesome.
Image
nx95240
KA-T.org Featured Ride
KA-T.org Featured Ride
Posts: 615
Joined: Tue Feb 24, 2004 5:59 pm
Location: Nooga,TN
Contact:

Post by nx95240 »

Structure240sx wrote:a few hundred rpms short is what it was

almost there buddy, im getting back to the dyno this week prolly
yea he cut it off SHORT because it got lean and i didnot not want anything to happen.because i made 444@ 22psi and that should have been around 515 or so @ 30psi . and i might look at some 91 cams this winter .
Structure240sx
KA-T.org Featured Ride
KA-T.org Featured Ride
Posts: 695
Joined: Thu Aug 12, 2004 11:50 am
Location: Sicklerville, NJ
Contact:

Post by Structure240sx »

of course right after i read this thread and looked back at my dyno. stopped at 6200rpms. prolly would have hit 540 or so on mine damnit. im going back this week with the new intake manifold. ill be sure to hit the revlimiter this time
klattr1
Forum Moderator
Posts: 3724
Joined: Mon Feb 02, 2004 10:22 pm
Location: Charlotte, NC
Contact:

Post by klattr1 »

rhd
240sx Wannabe
Posts: 101
Joined: Tue Oct 18, 2005 2:31 pm
Location: Taylorsville, NC

Post by rhd »

awesome job man....you're dead on for 500whp!
nx95240
KA-T.org Featured Ride
KA-T.org Featured Ride
Posts: 615
Joined: Tue Feb 24, 2004 5:59 pm
Location: Nooga,TN
Contact:

Post by nx95240 »

thanks man. i think it will get there next time.
Post Reply