Search found 18 matches
- Wed Jan 21, 2015 10:34 am
- Forum: KA-T Picture Threads
- Topic: Supakat's Thread
- Replies: 1796
- Views: 484610
Re: Supakat's Thread
Funny you say that, my CX-racing one snapped in the same spot, however I did purchase their heavier duty one and its great. I am pushing 26psi on my car daily and no issues yet. The old manifold welds were weak too. On the newer one I did re-weld a couple areas, gasket matched it and cleaned up the ...
Re: blown hg?
bad ringlands for sure. Factory pistons cannot handle boost as much as ppl want to think.....been through this before a few times before i finally upgraded
- Mon Sep 23, 2013 7:49 pm
- Forum: KA-T Tech. Advanced
- Topic: HOW TO RUN MAXIMA COILS ( UPDATED )
- Replies: 28
- Views: 31905
Re: HOW TO RUN MAXIMA COILS
Thanks. I got ahold of him and he walked me right through it
- Wed Sep 18, 2013 7:45 pm
- Forum: KA-T Tech. Advanced
- Topic: HOW TO RUN MAXIMA COILS ( UPDATED )
- Replies: 28
- Views: 31905
Re: HOW TO RUN MAXIMA COILS
^^^bump^^^
- Tue Aug 27, 2013 12:49 pm
- Forum: KA-T Tech. Advanced
- Topic: HOW TO RUN MAXIMA COILS ( UPDATED )
- Replies: 28
- Views: 31905
Re: HOW TO RUN MAXIMA COILS
What would I need to load for the aem setup to run these coils. I have the aem series 2 and maxima coils I want to install. Has anyone done this to a aem ems what pins do I need to hook up. All help without bashing would be great
- Sat Mar 16, 2013 5:56 pm
- Forum: Dyno Results
- Topic: 609hp/512tq @ 20 psi
- Replies: 24
- Views: 11947
- Wed Mar 06, 2013 9:32 am
- Forum: KA-T Chat
- Topic: Phx Meet/Show
- Replies: 2
- Views: 1015
- Mon Mar 04, 2013 2:27 pm
- Forum: KA-T Chat
- Topic: Phx Meet/Show
- Replies: 2
- Views: 1015
Phx Meet/Show
I have a huge parking lot available to have car meets/shows that is safe and no cops ;) . I was wondering if I put all this together how many PHX ppl would show with their KA's, or really any other decent car..... Let me know you think, a KA meet would be b!itchin`every week or every other week. Chi...
- Wed Aug 08, 2012 9:12 pm
- Forum: KA-T Chat
- Topic: Free set of stage 2 cams for ka24de
- Replies: 85
- Views: 32389
- Fri Jun 15, 2012 4:11 pm
- Forum: Welding/Fabrication
- Topic: Distributor delete cap
- Replies: 2
- Views: 2920
- Fri Jun 15, 2012 2:18 pm
- Forum: Welding/Fabrication
- Topic: Distributor delete cap
- Replies: 2
- Views: 2920
Distributor delete cap
Hey all help needed. I am going to be doing the maxima coil on plug. So far I do not know what to do with the distributor cap after I convert. I have seen pics on here of ppl running them open but I would prefer a CNC cap to protect the optics and the cas disk from debris. Does n e one know where I ...
- Thu Jun 14, 2012 9:06 pm
- Forum: KA-T Picture Threads
- Topic: *Post Your Engine Bay Pics*
- Replies: 922
- Views: 422411
- Thu Jun 14, 2012 8:59 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
- Thu Jun 14, 2012 8:53 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
- Thu Jun 14, 2012 7:22 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
- Thu Jun 14, 2012 7:19 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
- Thu Jun 14, 2012 6:43 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
- Thu Jun 14, 2012 6:41 pm
- Forum: Introductions
- Topic: Boosting in PHX
- Replies: 7
- Views: 1887
Boosting in PHX
What's up everyOne. Names bill. I have a 1995 kouki. Fully forged bottom end Supertech uppers. Gt3076 ball bearing. 248/248 swap. Jwt sprockets. Aem standalone. 600cc jecs. Godspeed intake. Just getting it back from dyno tomorrow. Ums did the tune. They told me 404whp 316 torque 18psi boost. Sounds ...